Shengbo Chai

Prof. Shengbo Chai


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 October 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SCShengbo Chai
Shengbo Chai
QZQingyu Zhao
Qingyu Zhao
CZCailin Zheng
Cailin Zheng
SCShang Chen
Shang Chen
In suspension bridges employing spatial cables, the main cables undergo torsion during the construction process. Clarifying the distribution pattern of the main cable torsional angle can guide the positioning and installation of cable clamps and mitigate issues such as wire waving. This paper provides a theoretical calculation method for the distribution law of the torsion angle of the main cable. Firstly, it is assumed that the load form that causes the torsion of the main cable is the uniform load along the cable length and the span length. The theoretical calculation formulas of the torsion angle are derived, respectively, and the two formulas are compared. Analysis shows that under a uniformly distributed load, when the main cable is deflected at a certain angle, the torque is non-uniformly distributed along the cable, and the torsional angle follows a fourth-order parabolic curve along the span. A model test on spatial cable deflection was conducted, and the measured torsional angles were compared with theoretical results. The findings indicate that the measured torsional angle variation along the span is generally consistent with theoretical calculations. When the deflection angle of the spatial cable is large, the theoretical value exceeds the measured value. Furthermore, a finite element model was employed to calculate the torsional angle, torque, and bending moment during cable deflection. The results reveal that the distribution of the torsional angle depends on the ratio of the moment of inertia and the polar moment of inertia of the main cable section. The smaller the polar moment of inertia relative to the moment of inertia, the closer the torsional angle is to the spatial deflection angle. When the polar moment of inertia is relatively small, except in the end regions, the distribution of torque obtained from simulations is largely consistent with the theoretical values.

26 December 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
XWXiulan Wang
Xiulan Wang
SCShengbo Chai
Shengbo Chai
MWMaoqiang Wang
Maoqiang Wang
QWQian Wu
Qian Wu
KHKaijie Huang
Kaijie Huang
To investigate the anti-slip characteristics of the main cables in a three-tower suspension bridge with spatial cable systems, this paper proposes an analytical calculation method for the anti-slip safety factor of the main cables and establishes an equivalent mechanical analysis model for multi-tower suspension bridges with spatial cable systems. Based on the deformation of the towers and cables under live load, as well as the equilibrium relationship of the main cable forces in loaded and unloaded spans, analytical formulas for the anti-slip safety factor of the main cables at the middle tower saddle are derived. A finite element model is developed to validate the formulas. The influence of parameters such as the spatial cable inclination angle, tower-to-cable stiffness ratio, dead-to-live load ratio, sag-to-span ratio, span length, and friction coefficient between the main cable and saddle on the anti-slip safety factor is analyzed. The results indicate that the formula proposed in this paper provides a highly accurate estimation of the slip resistance safety factor for main cables in spatial cable multi-tower suspension bridges. The adoption of spatial main cable configuration enhances the stability of the slip resistance safety factor at the intermediate tower saddle. The slip resistance safety factor of the main cable decreases with the increase in the tower-to-cable stiffness ratio, while it increases with the rise in the sag-to-span ratio. Moreover, the influence of the sag-to-span ratio on the slip resistance stability of the main cable becomes more pronounced with higher tower stiffness. The slip resistance safety factor of the main cable exhibits an approximately linear increase with the rise in the dead-to-live load ratio and the coefficient of friction. Furthermore, the slip resistance safety factor increases with the span length, and this rate of increase becomes more pronounced with smaller sag-to-span ratios. The research findings presented in this paper provide a theoretical basis for the design of spatial cable multi-tower suspension bridges.