Hongsuk Kim

Dr. Hongsuk Kim

Korea Institute of Machinery & Materials
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

16 September 2019 in International Journal of Automotive Technology
Verified
Journal Article
Closed access
PDF file
JHJoonsoo Han
Joonsoo Han
TKTaemin Kim
Taemin Kim
HJHaksup Jung
Haksup Jung
SPSukang Pyo
Sukang Pyo
GCGyubaek Cho
Gyubaek Cho
HKHongsuk Kim
Hongsuk Kim

10 June 2020 in International Journal of Engine Research
Verified
Journal Article
Closed access
PDF file
WKWonmo Kang
Wonmo Kang
SPSukang Pyo
Sukang Pyo
HKHongsuk Kim
Hongsuk Kim
Diesel particulate filter regeneration using intake and exhaust throttling is technically simple and economically efficient compared to other methods. The purpose of this study is to investigate not only the reasons for the increase in exhaust temperature during intake or exhaust throttling but also their feasibility as a diesel particulate filter regeneration technology. In this study, a non-road diesel engine having a mechanical fuel injection pump was used for experiments. The changes in exhaust temperatures were measured during intake and exhaust throttling for the no-load maximum revolutions per minute engine condition. The experimental results exhibited that both intake and exhaust throttling reduced the intake air mass flow rate and increased piston pumping, which then increased fuel consumption. These effects were the primary reasons for increasing the temperature of exhaust gases. In particular, intake throttling was more effective than exhaust throttling in terms of reducing the intake air mass flow rate. However, exhaust throttling caused larger pumping losses, resulting in higher fuel consumption. Furthermore, in case of exhaust throttling, engine combustion was possible even at high equivalence ratios because of the larger amounts of residual gases in the combustion chamber. In summary, exhaust throttling is more effective for regenerating a diesel particulate filter at a high temperature than intake throttling. In addition, this study verified the feasibility of diesel particulate filter regeneration using exhaust throttling through analyses of diesel particulate filter regeneration efficiency, fuel consumption, and exhaust concentration when regenerating the diesel particulate filter by increasing the exhaust temperature through exhaust throttling.

26 April 2016 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
SYSungjun Yoon
Sungjun Yoon
HKHongsuk Kim
Hongsuk Kim
DKDaesik Kim
Daesik Kim
SPSungwook Park
Sungwook Park
Stringent emission regulations (e.g., Euro-6) have forced automotive manufacturers to equip a diesel particulate filter (DPF) on diesel cars. Generally, postinjection is used as a method to regenerate the DPF. However, it is known that postinjection deteriorates the specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration is one of the key technologies for diesel powertrains equipped with a DPF. This paper presents correlations between the fuel injection strategy and exhaust gas temperature for DPF regeneration. The experimental apparatus consists of a single-cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, the postinjection timing was in the range of 40 deg aTDC to 110 deg aTDC and double postinjection was considered. In addition, the effects of the injection pressure were investigated. The engine load was varied among low load to midload conditions, and the amount of fuel of postinjection was increased up to 10 mg/stk. The oil dilution during the fuel injection and combustion processes was estimated by the diesel loss measured by comparing two global equivalences ratios: one measured from a lambda sensor installed at the exhaust port and one estimated from the intake air mass and injected fuel mass. In the present study, the differences of the global equivalence ratios were mainly caused by the oil dilution during postinjection. The experimental results of the present study suggest optimal engine operating conditions including the fuel injection strategy to obtain an appropriate exhaust gas temperature for DPF regeneration. The experimental results of the exhaust gas temperature distributions for various engine operating conditions are discussed. In addition, it was revealed that the amount of oil dilution was reduced by splitting the postinjection (i.e., double postinjection). The effects of the injection pressure on the exhaust gas temperature were dependent on the combustion phasing and injection strategies.

5 August 2017 in International Journal of Automotive Technology
Verified
Journal Article
Closed access
PDF file
JHJoonsoo Han
Joonsoo Han
JLJunho Lee
Junho Lee
YOYoungtaig Oh
Youngtaig Oh
GCGyubaek Cho
Gyubaek Cho
HKHongsuk Kim
Hongsuk Kim

7 March 2025 in Energy
Verified
Journal Article
Open access
YKYanghwa Kim
Yanghwa Kim
OLOcktaeck Lim
Ocktaeck Lim
GCGyubaek Cho
Gyubaek Cho
HKHongsuk Kim
Hongsuk Kim