In this article, we propose a switching anti-windup scheme for the aircraft engine control. The linear engine model with asymmetric saturation is first transformed into a switched system, each subsystem of which is subject to symmetric saturation. A state-dependent switching logic is presented to orchestrate the switching among multiple anti-windup compensators. We then establish the sufficient condition to guarantee the regional stability and $\mathcal {L}_{2}$ performance of the resulting closed-loop system. This condition is less conservative since the non-symmetric nature of the saturation nonlinearity can be fully exploited in the control design. Optimization algorithms are further developed for the anti-windup gain design. The theoretical aspect of the proposed method is analyzed rigorously, and the effectiveness is validated through experiments performed on a semi-physical test bed.
This article proposes a switching anti-windup strategy for linear, time-invariant (LTI) systems subject to asymmetric actuator saturation and $\mathcal{L}_{2}$ -disturbances, the core idea behind which is to make full use of the available range of control input space by switching among multiple anti-windup gains. The asymmetrically saturated LTI system is converted to a switched system with symmetrically saturated subsystems, and a dwell time switching rule is presented to govern the switching between different antiwindup gains. Based on multiple Lyapunov functions, we derive sufficient conditions for guaranteeing the regional stability and weighted $\mathcal{L}_{2}$ performance of the closed-loop system. The switching anti-windup synthesis that designs a separate anti-windup gain for each subsystem is cast as a convex optimization problem. In comparison with the design of a single anti-windup gain, our method can induce less conservative results since the asymmetric character of the saturation constraint is fully utilized in the switching anti-windup design. Two numerical examples, and an application to aeroengine control (the experiments are conducted on a semiphysical test bench), demonstrate the superiority and practicality of the proposed scheme.
16 April 2024 in IEEE Transactions on Aerospace and Electronic Systems
Given that thrust is the most core parameter of turbofan engines but cannot be measured, and that engines are subject to performance degradation, disturbances, or even failure, this paper presents a direct thrust control (DTC) system based on an onboard model and robust control. To overcome the limitations of the unscented Kalman filter (UKF) in terms of accuracy and convergence speed, the Levenberg-Marquardt (L-M) algorithm is employed to optimize the measurement update process, thereby establishing a superior onboard model for turbofan engines. Then, to address the real-time issue, the LSTM network is trained to approximate the nonlinear engine model used for the Kalman observer, substantially accelerating the computational efficiency. Finally, based on this onboard model, an H∞ gain-scheduled controller is designed for the DTC system. The comparative results of numerical simulations and hardware experiments on the Xavier embedded controller substantiate the feasibility, superiority, and real-time performance of our approaches, thus suggesting the potential for practical engineering.
A method based on OEMD (Orthogonal Empirical Mode Decomposition) and the theory of time-frequency entropy was applied to detect different rail fastener conditions. The original vertical vibration acceleration response of rail under different fastening conditions was obtained from outdoor experiment. The OEMD method was used to get orthogonal IMFs (Intrinsic Mode Functions) of the original vibration signal. The Hilbert time-frequency spectrum was then obtained based on the orthogonal IMFs and corresponding entropy was calculated and compared. The results show that the method is available to detect different rail fastener conditions.
25 March 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief proposes a novel anti-windup scheme for linear systems subject to asymmetric input saturation. The asymmetrically saturated system is converted into an equivalent one with symmetric saturation through coordinate transformation. Based on the transformed model, we establish the set invariance condition of the resulting closed-loop system. This condition is less conservative since the non-symmetric nature of the saturation nonlinearity can be fully exploited in the control design. An optimization algorithm to maximize the invariant set is further developed for anti-windup gain design. The theoretical aspect of this method is analyzed rigorously, and the effectiveness is verified through an application to the aircraft engine control with experiments performed on a semi-physical test bed.
25 December 2023 in IEEE Transactions on Aerospace and Electronic Systems
This article investigates the anti-windup synthesis problem for linear, time-invariant systems subject to asymmetric input magnitude and rate saturation (MRS) under a switching control framework. By developing an MRS model, the original system is augmented as a linear system with magnitude-only saturation. We then partition the input space into several regions based on the signs of the control inputs. The original asymmetric saturation function can be equivalently expressed as a symmetric one in each of these regions, and the saturation levels associated with different regions are different. By utilizing these special properties, we design a separate anti-windup gain for each region of the input space. The switching from one anti-windup gain to another is activated when the input signals leave one region for another. In comparison with the single gain anti-windup design, this switching anti-windup design can lead to better performance, since the switching among multiple anti-windup gains makes fully use of the input capacity. Finally, the proposed method is applied to the aircraft engines. Hardware-in-the-loop testing demonstrates its superiority and practicality.