Fouling development in direct contact membrane distillation (DCMD) for seawater desalination was evaluated combining in-situ monitoring performed using optical coherence tomography (OCT) together with destructive techniques. The non-invasive monitoring with OCT provided a better understanding of the fouling mechanism by giving an appropriate sampling timing for the membrane autopsy. The on-line monitoring system allowed linking the flux trend with the structure of fouling deposited on the membrane surface. The water vapor flux trend was divided in three phases based on the deposition and formation of different foulants over time. The initial flux decline was due to the deposition of a 50-70 nm porous fouling layer consisting of a mixture of organic compounds and salts. Liquid chromatography with organic carbon detection (LC-OCD) analysis revealed the abundance of biopolymer in the fouling layer formed at the initial phase. In the second phase, formation of carbonate crystals on the membrane surface was observed but did not affect the flux significantly. In the last phase, the water vapor flux dropped to almost zero due to the deposition of a dense thick layer of sulfate crystals on the membrane surface.

Aquaporin plays a promising role in fabricating high performance biomimetic forward osmosis (FO) membranes. However, aquaporin as a protein also has a risk of denaturation caused by various chemicals, resulting in a possible decay of membrane performance. The present study tested a novel aquaporin based biomimetic membrane in simulated membrane cleaning processes. The effects of cleaning agents on water flux and salt rejection were evaluated. The membrane showed a good resistance to the chemical agents. The water flux after chemical cleaning showed significant increases, particularly after cleaning with NaOCl and Alconox. Changes in the membrane structure and increased hydrophilicity in the surrounding areas of the aquaporin may be accountable for the increase in water permeability. The membrane shows stable salt rejection up to 99% after all cleaning agents were tested. A 15-day experiment with secondary wastewater effluent as the feed solution and seawater as the draw solution showed a stable flux and high salt rejection. The average rejection of the dissolved organic carbon from wastewater after the 15-day test was 90%. The results demonstrated that the aquaporin based biomimetic FO membrane exhibits chemical resistance for most agents used in membrane cleaning procedures, maintaining a stable flux and high salt rejection

Gravity-driven membrane (GDM) filtration is one of the promising membrane bioreactor (MBR) configurations. It operates at an ultra-low pressure by gravity, requiring a minimal energy. The objective of this study was to understand the performance of GDM filtration system and characterize the biofouling formation on a flat sheet membrane. This submerged GDM reactor was operated at constant gravitational pressure in treating of two different concentrations of secondary wastewater effluent. Morphology of biofilm layer was acquired by an in-situ and on-line optical coherence tomography (OCT) scanning in a fixed position at regular intervals. The thickness and roughness calculated from OCT images were related to the variation of flux, fouling resistance and permeate quality. At the end of experiment, fouling was quantified by total organic carbon (TOC) and adenosine tri-phosphate (ATP) method. Confocal laser scanning microscopy (CLSM) was also applied for biofouling morphology observation. The biofouling formed on membrane surface was mostly removed by physical cleaning confirmed by contact angle measurement before and after cleaning. This demonstrated that fouling on the membrane under ultra-low pressure operation was highly reversible. The superiority and sustainability of GDM in both flux maintaining and long-term operation with production of high quality effluent was demonstrated

One of the major challenges in membrane distillation (MD) desalination is scaling, mainly CaSO4 and CaCO3. In this study, in order to achieve a better understanding and establish a strategy for controlling scaling, a detailed investigation on the MD scaling was performed by using various analytical methods, especially an in-situ monitoring technique using an optical coherence tomography (OCT) to observe the cross-sectional view on the membrane surface during operation. Different concentrations of CaSO4, CaCO3, as well as NaCl were tested separately and in different mixed feed solutions. Results showed that when CaSO4 alone was employed in the feed solution, the mean permeate flux (MPF) has significantly dropped at lower volume concentration factor (VCF) compared to other feed solutions and this critical point was observed to be influenced by the solubility changes of CaSO4 resulting from the various inlet feed temperatures. Although the inlet feed and permeate flow rates could contribute to the initial MPF value, the VCF, which showed a sharp MPF decline, was not affected. It was clearly observed that the scaling on the membrane surface due to crystal growth in the bulk and the deposition of aggregated crystals on the membrane surface abruptly appeared close to the critical point of VCF by using OCT observation in a real time. On the other hand, NaCl + CaSO4 mixed feed solution resulted in a linear MPF decline as VCF increases and delayed the critical point to higher VCF values. In addition, CaCO3 alone in feed solution did not affect the scaling, however, when CaSO4 was added to CaCO3, the initial MPF decline and VCF met the critical point earlier. In summary, calcium scaling crystal formed at different conditions influenced the filtration dynamics and MD performances