Danilo Almeida Machado

Dr. Danilo Almeida Machado

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 April 2023 in International Journal of Multiphase Flow
Verified
Journal Article
Closed access
GDGabriel Silva Dias
Gabriel Silva Dias
DMDanilo Almeida Machado
Danilo Almeida Machado
JAJosé Carlos de Andrade
José Carlos de Andrade
FCFernando de Souza Costa
Fernando de Souza Costa

21 June 2024 in Combustion and Flame
Verified
Journal Article
Closed access
FMFábio A.S. Mota
Fábio A.S. Mota
GDGabriel S. Dias
Gabriel S. Dias
DMDanilo Almeida Machado
Danilo Almeida Machado
JAJosé C. Andrade
José C. Andrade
FCFernando S. Costa
Fernando S. Costa
Chenglong TangChenglong Tang
Chenglong Tang

30 October 2022 in Flow, Turbulence and Combustion
Verified
Journal Article
Closed access
PDF file
DMDanilo Almeida Machado
Danilo Almeida Machado
FCFernando de Souza Costa
Fernando de Souza Costa
JAJosé Carlos de Andrade
José Carlos de Andrade
GDGabriel Silva Dias
Gabriel Silva Dias
GFGustavo Alexandre Achilles Fischer
Gustavo Alexandre Achilles Fischer

19 July 2023 in Measurement Science and Technology
Verified
Journal Article
Closed access
DMDanilo Almeida Machado
Danilo Almeida Machado
FCF S Costa
F S Costa
JAJ C Andrade
J C Andrade
GFG A A Fischer
G A A Fischer
This study presents a comparative analysis of droplet and conical liquid film velocities in sprays by a pressure swirl injector with Abramovich geometric constant K = 1.986. The velocities were measured simultaneously by schlieren image velocimetry and sequential images of the liquid film, using a high-speed camera with 8192 fps and shutter of 2 μs. Other parameters, such as discharge coefficients, spray cone angles and breakup lengths were also determined, using water as test fluid, for injection pressures from 0.05 to 0.5 MPa. Experimental velocity data were compared to results from different semi-empirical equations. The breakup lengths decreased continuously from around 20 mm to 15 mm for injection pressures from 0.1 to 0.5 MPa, while spray cone angles increased continuously from about 42°–53°, for pressures from 0.2 to 0.5 MPa. Mean axial droplet velocities varied from 4.7 m s−1 to 14.5 m s−1, while the mean total droplet velocities varied from 5 m s−1 to 16.2 m s−1 and the total liquid film velocity increased from 5.7 m s−1 to 20.2 m s−1, approximately, for increasing injection pressure. Liquid film velocities were about 15%–28% higher than the droplet velocities in the pressure range considered, due to the energy required for liquid film breakup and the air drag on the droplets. The current findings underscore that significant discrepancies may arise when relying on inadequate velocity data, particularly when employed in the computation of key parameters such as the Reynolds and Weber numbers.

22 August 2025 in Chemical Engineering Science
Verified
Journal Article
Closed access
DMDanilo Almeida Machado
Danilo Almeida Machado
FCFernando de Souza Costa
Fernando de Souza Costa
JAJosé Carlos de Andrade
José Carlos de Andrade
ISIgor Paccini Silva
Igor Paccini Silva
GDGabriel Silva Dias
Gabriel Silva Dias
LSLuiz Fernando Grespan Setz
Luiz Fernando Grespan Setz

30 December 2024 in Measurement Science and Technology
Verified
Journal Article
Closed access
DMDanilo Almeida Machado
Danilo Almeida Machado
FCFernando S Costa
Fernando S Costa
GDGabriel S Dias
Gabriel S Dias
FMFábio A S Mota
Fábio A S Mota
Pressure swirl injectors generate conical hollow sprays with a liquid film adjacent to the exit nozzle. This paper describes macroscopic and microscopic parameters of sprays and disturbances of the liquid films formed by dual pressure swirl injectors, utilizing a telecentric shadowgraphy optical system. High-speed images with kHz frequencies were used for the simultaneous measurement of spray cone angles, breakup lengths, mean droplet velocities and wave amplitude ratios. Two injectors were tested with inner nozzles having Abramovich geometric constants K int = 2 and 2.125 and external nozzles with geometric constants K ext = 2.9 and 1.9792, respectively. Water was used as test fluid and the injection pressures were varied from 0.05 to 0.5 MPa. Simultaneous data from the same set of images allowed the calculation of the maximum surface wave growth rate. The results indicated that the maximum surface wave growth rate varies approximately linearly with the injection pressure. Measured maximum amplitude ratios of the conical liquid film disturbances varied in the range 2.32 < ln ⁡ ( η bu / η 0 ) < 4.61, relatively close to recent experimental data on conical liquid films, but significantly lower than the calculated values for planar liquid films. The maximum amplitude ratio is a crucial parameter to determine breakup lengths. A new semi-empirical equation is proposed to describe the disturbance ratios of conical liquid films of pressure swirl injectors.