zeqin Cui

Dr. zeqin Cui


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2019 in Materials Science and Engineering: C
Verified
Journal Article
Closed access
ZCzeqin Cui
zeqin Cui
YZYakai Zhang
Yakai Zhang
YCYinlong Cheng
Yinlong Cheng
DGDianqing Gong
Dianqing Gong
WWWenxian Wang
Wenxian Wang

1 June 2020 in Surface and Coatings Technology
Verified
Journal Article
Closed access
ZCzeqin Cui
zeqin Cui
SLShang Li
Shang Li
JZJun Zhou
Jun Zhou
ZMZhihao Ma
Zhihao Ma
WZWei Zhang
Wei Zhang
PDPeng Dong
Peng Dong

1 January 2015 in Chinese Optics Letters
Verified
Journal Article
Closed access
ZCzeqin Cui
zeqin Cui
YYYingqiLi YingqiLi
YingqiLi YingqiLi
WWWenxian Wang
Wenxian Wang
CLChenghsiang Lin
Chenghsiang Lin
BXBingshe Xu
Bingshe Xu
We investigate the influence of environmental media on ablation rate of AISI 443 stainless steel under femtosecond (fs) laser single raster scan and multiple raster scans in air, water, and methanol. Meanwhile, the development of ablation rate with the change of fs laser-induced surface morphology in the three environmental media is comparatively studied. The results show that environmental media as well as fs laser-induced morphology control the ablation rate with the increasing number of raster scans (N). Under single raster scanning (N = 1), the ablation rate is higher in liquid than in air due to the confinement of plasma, laser-induced shockwaves, and bubble-related mechanical forces. However, under multiple raster scans, the variation in ablation rate with the increase in N in these three environmental media is complicated and is largely determined by the surface morphology induced by previous fs laser ablation. When N > 20, the ablation rate is much higher in air than in liquids due to preferential ablation caused by the formation of nanostructures-textured mound-shaped microstructures in air. Besides, the redeposition of ejected ablated materials is also an important factor that affects the ablation depth.

19 September 2016 in Advanced Engineering Materials
Verified
Journal Article
Closed access
PDF file
PGPushan Guo
Pushan Guo
ZCzeqin Cui
zeqin Cui
LYLijing Yang
Lijing Yang
LCLinxin Cheng
Linxin Cheng
WWWenxian Wang
Wenxian Wang
BXBingshe Xu
Bingshe Xu

8 April 2023 in Acta Metallurgica Sinica (English Letters)
Verified
Journal Article
Closed access
PDF file
LLLiwei Lan
Liwei Lan
WWWenxian Wang
Wenxian Wang
ZCzeqin Cui
zeqin Cui
XHXiaohu Hao
Xiaohu Hao

6 July 2018 in Materials
Verified
Journal Article
Open access
PDF file
WCWeili Cheng
Weili Cheng
YZYao Zhang
Yao Zhang
SMShichao Ma
Shichao Ma
SASrinivasan Arthanari
Srinivasan Arthanari
ZCzeqin Cui
zeqin Cui
Lifei WangLifei Wang
Lifei Wang
A low-alloyed Mg–Sn–Al–Zn system was developed and successfully fabricated through the extrusion process. The dependence of tensile properties and corrosion behavior on microstructural characteristics of the studied alloy has been investigated. After extrusion, the alloy consists of fine dynamically recrystallized (DRXed) grains of ~2.65 μm and strongly textured coarse unDRXed grains. As a consequence, the extruded alloy showed a high-tensile yield strength (YS) of 259 MPa, ultimate tensile strength (UTS) of 297 MPa and elongation (EL) of 19.0%. The strengthening response was discussed in terms of grain size, texture and solutes. The as-extruded alloy presented severe pitting corrosion and the dependence of corrosion properties on the crystallographic orientation and the formation of corrosion products was analyzed.