Enhanced oil recovery (EOR) from heavy oil reservoirs is challenging. High oil viscosity, high mobility ratio, inadequate sweep, and reservoir heterogeneity adds more challenges and severe difficulties during any EOR method. Foam injection showed potential as an EOR method for challenging and heterogeneous reservoirs containing light oil. However, the foams and especially polymer enhanced foams (PEF) for heavy oil recovery have been less studied. This study aims to evaluate the performance of CO2 foam and CO2 PEF for heavy oil recovery and CO2 storage by analyzing flow through porous media pressure profile, oil recovery, and CO2 gas production. Foam bulk stability tests showed higher stability of PEF compared to that of surfactant-based foam both in the absence and presence of heavy crude oil. The addition of polymer to surfactant-based foam significantly improved its dynamic stability during foam flow experiments. CO2 PEF propagated faster with higher apparent viscosity and resulted in more oil recovery compared to that of CO2 foam injection. The visual observation of glass column demonstrated stable frontal displacement and higher sweep efficiency of PEF compared to that of conventional foam. In the fractured rock sample, additional heavy oil recovery was obtained by liquid diversion into the matrix area rather than gas diversion. Aside from oil production, the higher stability of PEF resulted in more gas storage compared to conventional foam. This study shows that CO2 PEF could significantly improve heavy oil recovery and CO2 storage.
Inadequate sweep efficiency is one of the main concerns in conventional heavy oil recovery processes. Alternative processes are therefore needed to increase heavy oil sweep efficiency. Foam injection has gained interest in conventional oil recovery in recent times as it can control the mobility ratio and improve the sweep efficiency over chemical or gas flooding. However, most of the studies have focused on light crude oil. This study aims to investigate the static and dynamic performances of foam and polymer-enhanced foam (PEF) in the presence of heavy oil. Static and dynamic experiments were conducted to investigate the potential of foam and PEF for heavy oil recovery. Static analysis included foam/PEF stability, decay profile, and image analysis. A linear visual sand pack was used to visualize the performance of CO2 foam and CO2 PEF in porous media (dynamic experiments). Nonionic, anionic, and cationic surfactants were used as the foaming agents. Static stability results showed that the anionic surfactant generated relatively more stable foam, even in the presence of heavy oil. Slower liquid drainage and collapse rates for PEF compared to that of foam were the key observations through foam static analyses. Besides improving heavy oil recovery, the addition of polymer accelerated foam generation and propagation in porous media saturated with heavy oil. Visual analysis demonstrated more stable frontal displacement and higher sweep efficiency of PEF compared to conventional foam flooding. Unlike foam injection, lesser channeling (foam collapse) was observed during PEF injection. The results of this study will open a new insight on the potential of foam, especially polymer-enhanced foam, for oil recovery of those reservoirs with viscous oil.
Nanoparticle stabilized emulsions have drawn increasing attention for applications in various industries including enhanced oil recovery (EOR). Unlike surfactants, nanoparticles provide long-term stability to the emulsions and significantly higher viscoelastic response. However, the flow behavior of nanoparticle stabilized emulsions in porous media has not been explored much. Cellulose Nanocrystals (CNCs) have gained attention in the past few years since they are an abundant renewable biomass-derived material. This study investigates the flow behavior and stability of oil in water emulsions stabilized by CNCs in unconsolidated porous media and the application of these emulsions in EOR and conformance control. Confocal Microscopy coupled with Cryo-SEM enabled us to precisely characterize the emulsion microstructure and correlate it to the rheological behavior of the emulsions. The rheological measurements revealed that a strong droplet network forms within the emulsions over time. Importantly, we show that the same network forms when the emulsions occupy pore space in a granular material. Emulsions were injected through a sandpack with a porosity of 35% and average pore diameter of 54 μm. The injected emulsions were aged inside the porous media for 24 hours. Thorough experimental assessment of the collected effluent samples revealed that the emulsion was stable. The porous medium was then subjected to a gradually increasing pressure gradient of either water or oil. Gradients greatly exceeding typical near-well values (>300 psi/ft) were required to establish flow, and the resulting flow rate exhibited a pressure gradient three orders of magnitude higher than in an untreated water saturated sandpack. Interestingly, a significantly larger gradient was needed for water to flow than for oil, raising the possibility of using this class of emulsions for selective phase blocking, and perhaps as relative permeability modifiers. Moreover, emulsions stabilized with other material allowed water to flow at very small gradients, confirming that the network formation is critical for this application. This study revealed the potential application of a naturally occurring biodegradable nanomaterial for conformance control and for curbing excessive water production where zonal isolation is difficult to achieve.