Illia Bilous

Illia Bilous

Auto-generated profile, based on publicly available information

Illia Bilous


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 September 2025 in Central Ukrainian Scientific Bulletin. Technical Sciences
Verified
Journal Article
Closed access
EAElchyn Aliiev
Elchyn Aliiev
IBIllia Bilous
Illia Bilous
Elchyn Aliiev, Senior Researcher, Doctor of Technical Sciences, Professor of the Department of Engineering of Technical Systems, Dnipro State Agrarian and Economic University, Dnipro, Ukraine, ORCID: https://orcid.org/0000-0003-4006-8803, e-mail: aliev@meta.ua Illia Bilous, PhD student in Industrial Mechanical Engineering, Assistant of the Department of Engineering of Technical Systems, Dnipro State Agrarian and Economic University, Dnipro, Ukraine, ORCID: https://orcid.org/0000-0001-9635-6631, e-mail: bilous.i.m@dsau.dp.ua The aim of the research is to perform numerical modeling of the concentrated feed grinding process and to determine the influence of the physical and mechanical properties of the grain, its orientation, and the parameters of the disc crusher on the fracture force during impact cutting. Considering the specific design of the new working unit of the disc crusher with impact inserts, the influence of three key factors – distance between impact inserts (l), angle between them (α), and the linear velocity of insert motion (V) – was investigated through numerical simulation of the grain fracture process for corn, wheat, and barley using the discrete element method (DEM) in the Simcenter STAR-CCM+ environment. The patterns of fracture force for corn, wheat, and barley grains under three orientations during impact cutting were established depending on the distance between inserts, the angle between them, and the linear velocity. The identified patterns provide a quantitative assessment and a deeper physical understanding of the grain shell destruction processes under impact cutting conditions. This serves as a basis for optimizing the design parameters of the crusher to enhance the efficiency and energy savings in processing different types of grain materials. To comprehensively evaluate the grain grinding process, an integral efficiency criterion was proposed, aiming to minimize fracture force at maximum distance between inserts and minimum insert speed. This allows for high process productivity while simultaneously reducing kinetic energy consumption. Rational grinding parameters were established for the main cereal crops – corn, wheat, and barley. The analysis of the obtained results confirms that the process parameters (distance between inserts l = 1.68–1.79 mm, installation angle β = 21.8–25.3°, insert velocity V = 4.72–5.86 m/s, disk rotation speed n = 1503–1865 rpm, modular clearance δ = 0.68–0.79 mm) reflect the physical and mechanical characteristics of each crop.

2 December 2023 in Engineering, Energy, Transport AIC
Verified
Journal Article
Closed access
VDVolodymyr Dudin
Volodymyr Dudin
IBIllia Bilous
Illia Bilous
In the structure of the product's production, feed is in the first place and accounts for 60-70% of the total cost. The effectiveness of stagnation of concentrated feed depends on the quality of their preparation, and the uniformity of detail and type of fractional stock of animal husbandry products. In the midst of all the development of methods of refinement and design solutions for the greatest expansion for the refinement of feed grain, hammer mills have emerged, which, unlike any other in the world, provide energy saving, with fine grinding up to 40% of the saw-like fraction, and for coarse grains - up to 20% of whole and incomplete grains. At the same time, disk-type grain trimming designs are becoming more and more widespread in the world. Such structures are developed from hammer construction with lower energy consumption and higher yield of the finished product. Therefore, further research aimed at improving the efficiency of the work of disk workers is relevant. Experimental studies of disk grain processing were carried out based on the theoretical design of the experiment, which was why mathematical models of processes were selected in the form of regression. The factors in the experiment were the frequency of disk wrapping n (x1), the modular gap between the disks m (x2) and the moisture content of the grain W (x3). Optimization criteria are the energy density of the detail q (y1) and the uniformity of k (y2). The energy intensity of the process began as a balance between effort and productivity. Uniformity began as a relationship instead of often with rational parameters to the point of importance and was expressed in hundreds. As a result of experimental studies of disk grain processing, it has been established that the energy intensity of the process and the uniformity of the grain are dependent on all relevant factors, with which rational indicators are based on optimization criteria and do not match. The main task is to find the optimal variation of factors for two criteria, which makes it possible to confirm that the minimum energy intensity of the process is in the range q = 3.67…4.54 kWhour/t, one Particularity - k=86.5…92.6% at values of additional factors n=1260-1320 min-1; W=12.8-13.2% for a rational range of refinement steps.

11 November 2025 in Agriculture
Verified
Journal Article
Open access
PDF file
IBIllia Bilous
Illia Bilous
Algirdas JasinskasAlgirdas Jasinskas
Algirdas Jasinskas
VDVolodymyr Dudin
Volodymyr Dudin
Savelii KukharetsSavelii Kukharets
Savelii Kukharets
EAElchyn Aliiev
Elchyn Aliiev
TŪTomas Ūksas
Tomas Ūksas
The study examines the influence of key structural and technological parameters of a disc crusher with impact plates—the distance between liners, installation angle, and linear movement speed—on the crushing process of maize, wheat, and barley grains. Numerical modeling using the Discrete Element Method (DEM) in Simcenter STAR-CCM+ revealed patterns of variation in breaking force during impact cutting. An integral efficiency criterion was proposed to minimize the breaking force while maximizing productivity and reducing energy consumption. Rational process parameters were determined for each crop, considering their physico-mechanical properties: liner distance l = 1.68–1.79 mm, installation angle β = 21.8–25.3°, particle velocity V = 4.72–5.86 m/s, disc speed n = 1503–1865 rpm, and clearance δ = 0.68–0.79 mm. Experimental studies yielded models describing specific energy consumption, dust-like fraction, and crushing degree depending on the liner angle, number, and rotation speed. Optimization showed that energy consumption was lowest for wheat (3.63 kWh/t) and highest for barley (6.76 kWh/t). The dust fraction was greatest for maize (5.13%) and lowest for barley (1.34%). Optimal grinding regimes were found at n = 1500–1764 rpm, β = 15.9–17.7°, and z = 9 plates. The results confirm the efficiency of adapting crusher parameters to grain properties.

31 March 2025 in Vibrations in engineering and technology
Verified
Journal Article
Closed access
VDVolodymyr Dudin
Volodymyr Dudin
IBIllia Bilous
Illia Bilous
The article studies the efficiency of a disc grain mill for concentrated feed, considering its structural and technological parameters and the influence of operating factors on grinding quality. The analysis of existing grinding methods has shown that traditional hammer and roller mills have significant drawbacks, such as high energy consumption (8–15 kWh/t for hammer mills) and an uneven particle size distribution of the product. In this regard, experimental studies were conducted on the operation of a disc mill, which potentially offers higher energy efficiency and a more uniform particle distribution. The aim of the study is to determine the influence of the structural and technological parameters of a disc mill for concentrated feed on grinding quality and energy consumption. The study examined the impact of key factors, including the modular gap between the discs (0.6–1.6 mm), disc rotation speed (1500–3000 rpm), and grain feed rate into the grinding chamber (450–1350 kg/h) on productivity and grinding quality. It was found that increasing the modular gap leads to an increase in the proportion of large fractions (for example, for wheat, the mass fraction of particles retained on a 2 mm sieve increased from 13.1% to 79.4%). At the same time, mill productivity depended on the type of grain: for wheat, it ranged from 0.1–0.25 t/h with a specific energy consumption of 1.7–8.2 kWh/t; for barley, 0.075–0.18 t/h and 3.8–9.4 kWh/t; and for corn, 0.07–0.18 t/h and 2.9–7.2 kWh/t. The results obtained suggest that the disc mill can be recommended as an energy-efficient alternative to traditional grinders in compound feed production. Optimizing the structural and technological parameters allows for reduced energy consumption and improved uniformity of the particle size distribution of the final product, contributing to increased productivity in livestock farms.

23 December 2024 in Central Ukrainian Scientific Bulletin. Technical Sciences
Verified
Journal Article
Closed access
VDVolodymyr Dudin
Volodymyr Dudin
IBIllia Bilous
Illia Bilous
Volodymyr Dudin, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Dnipro State Agrarian and Economic University, Dnipro, Ukraine, e-mail: dudin.v.yu@dsau.dp.ua, ORCID ID: 0000-0002-1414-7690 Illia Bilous, PhD student, Dnipro State Agrarian and Economic University, Dnipro, Ukraine, bilous.i.m@dsau.dp.ua In modern mechanical engineering, Model-Based Systems Engineering (MBSE) has become widely adopted. One of its key concepts is the creation and testing of virtual models of the designed technical systems. Compared to traditional approaches, this method significantly reduces resources and development time for new machines or improvements to existing ones. However, the accuracy of modeling entirely depends on the precision of the input data used for simulation. This also applies to the process of feed material destruction, particularly corn kernels. To obtain reliable simulation results, it is necessary to create a model of a kernel that closely resembles the real one and assign it physical and mechanical parameters that most accurately correspond to the studied sample. The aim of this research is to create an adequate virtual model of a corn kernel in the Simcenter STAR-CCM+ environment by comparing the destruction force obtained virtually and in laboratory experiments. Based on measurements and a review of studies in the Simcenter STAR-CCM+ software, a discrete element model (DEM) was developed using the aggregation of 86 spheres, employing the Hertz-Mindlin contact model. A virtual full-factorial experiment was conducted, resulting in regression equations describing the dependence of the kernel destruction force on Poisson’s ratio (µp), Young’s modulus (Ep), and ultimate tensile and shear stress (Wp) under different loading directions. A laboratory test stand was developed and implemented, where experimental studies of the destruction force of corn kernels were conducted under conditions analogous to the virtual experiment. The comparison of results identified factor values at which the model matches the laboratory research findings: Young’s modulus Ep = 10 MPa, Poisson’s ratio µp = 0.48, and ultimate tensile and shear stress Wp = 2.4 MPa. The obtained results allow for refining the input parameters in corn kernel simulations, ensuring more accurate virtual studies of the destruction process under various interactions with working elements.