Elchyn Aliiev

Prof. Elchyn Aliiev

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Acta Periodica Technologica
Verified
Journal Article
Open access
PDF file
EAElchyn Aliiev
Elchyn Aliiev
AGAlexander Gavrilchenko
Alexander Gavrilchenko
HTHennadii Tesliuk
Hennadii Tesliuk
ATAlexander Tolstenko
Alexander Tolstenko
VKVitaliy Koshul’kO
Vitaliy Koshul’kO
The study of the sunflower seed separation process during its movement on the vibrating surface has been carried out in two stages. The first (theoretical) stage has been implemented in the software package STAR-CCM + using the corresponding physical models. The second stage is the conduct of experimental research on a pilot sample with a base of vibrating pneumatic PVS table. As a result of numerical simulation and experimental studies of the sunflower seed separation process during its movement on the vibrating surface, we have determined the dependences of the change in the distribution coefficient, productivity and power consumed by the vibrating pneumatic separator from the seed supply, the inclination angles of the vibrating surface, the frequency and amplitude of its oscillation and the velocity of the airflow V. The statistical analysis has shown that the correlation coefficient between the theoretical and experimental dependencies in the variation of the values of the factors in the given range is 0.88-0.92. The technological and constructive scheme of the adaptive vibrating pneumatic separator with rationally defined regime parameters (seed supply, airflow velocity, deck oscillation frequency, deck inclination angle) has been developed basing of the obtained theoretical and experimental dependencies, using the software which is based on the created algorithm, allowing to perform the technological process of sunflower seed mixtures separating by volume density with higher productivity and quality.

24 February 2022 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
EAElchyn Aliiev
Elchyn Aliiev
APAndriy Paliy
Andriy Paliy
VKViktor Kis
Viktor Kis
APAnatoliy Paliy
Anatoliy Paliy
RPRoman Petrov
Roman Petrov
LKLeonid Korniienko
Leonid Korniienko
One of the tasks that imply increasing the milk productivity of cows is to create optimal maintenance conditions that ensure the increased use of the genetic potential of cattle based on the implementation of engineering and technological solutions. A mathematical model has been built that links the technical and technological parameters of the vacuum system of milking equipment, namely, the value of the working vacuum P, the pulsation frequency n, the ratio of pulsation cycles, and the tension strength of milking rubber FH to cows’ milk yield rate V. The range of milking plant operating parameters for milking in the milk line has been determined, at which the milk yield rate is maximum: P=52 kPa, n=57.6–58.8 min–1, δ=0.59–0.64, FH=59.3–60.4 H. Under these parameters, the milk yield rate is V=1.48–1.53 l/min. The results of the multifactor experiment have helped construct an adequate mathematical model of the second order, which confirms the theoretical dependence of the influence of the technical and technological parameters of the vacuum system of milking equipment on milk yield rate and the air flow of the milking machine. Analysis of the mathematical model has made it possible to establish the rational structural and technological parameters for the vacuum system of a milking machine: the value of the working vacuum, P=50.6 kPa; pulsation frequency, n=55.9 min–1, the ratio of pulsation cycles and the tension force of milking rubber FH=64.8 H. Under these parameters, the milk yield rate is maximum: V=1.47–1.52 l/min; the air flow consumption of the milking machine is Q=2.19 m3/h. The mathematical model built fully reveals the influence of technical and technological parameters of milking equipment on the efficiency of machine milking. Owing to this, the issue related to the rational choice of equipment is resolved.

11 March 2020 in Helia
Verified
Journal Article
Closed access
PDF file
EAElchyn Aliiev
Elchyn Aliiev
The development of automated precision technologies for the phenotyping test of seeds by a complex of functional features in the selection process of sunflower is relevant and promising. The task of developing a device for the automatic phenotyping test of seeds and the algorithm for finding and isolating seeds based on color information was set. Research was conducted on a stand, which consisted of the following elements: Video Microscope Camera 1080 P 16MP HDMI USB manufactured by Eakins, a set of LEDs of three types (red, green, blue) and a personal computer. The results of experimental studies of the process of automatic phenotyping test of seeds of different sunflower varieties allowed us to establish an average error of determining the geometric dimensions of sunflower seeds (length L and width B) – 0.06 mm. The histograms of the color distribution of sunflower seeds in the RGB color space with different illumination are established. As a result of the analysis of the obtained histograms of the color distribution of sunflower seeds in the RGB color space it is established that in the case of color homogeneity, the discreteness of the channels with red illumination is most clearly seen. A device for automatic phenotyping test of seeds has been developed, which preserves the accuracy of individual measurement of the geometric dimensions of sunflower seeds, determining their shape and color, which corresponds to modern measuring tools, and provides low complexity and high technological implementation of the phenotyping test procedure (determination, ascertaining and identification) material, according to its morphological and marker features.

19 February 2021 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
APAndriy Paliy
Andriy Paliy
EAElchyn Aliiev
Elchyn Aliiev
APAnatoliy Paliy
Anatoliy Paliy
KIKaterina Ishchenko
Katerina Ishchenko
SSShkromada Shkromada
Shkromada Shkromada
VMValentyna Mohutova
Valentyna Mohutova
Preparing cows for milking is one of the most important operations. Not only the speed of milk production but also the quality of milk depends on the level of the work performed. One of the most effective ways to mechanize the preparation of cows for milking implies the development of a special mechanical brush that cleans and stimulates the teat skin. As a result, there is no need to use additional foam detergents and napkins to cleanse and disinfect teats. A device has been designed for cleansing teats with two rotating brushes. Theoretical studies of the interaction of cleansing elements of the device for mechanical removal of pollutants from the udder teats in the course of milking operation were carried out. Assuming constancy of the modulus of elasticity, shape and roughness of teats, linear and angular velocities of brushes, nap stiffness, and homogeneity of physical and mechanical properties of contaminants on the teat, dependence of force Fe of the mechanical device on length l of the cleansing element and its speed ω was established. Under the condition that force Fe of the mechanical device is smaller than force Fp which causes pain but greater than the force retaining pollutants (adhesion), values of the main design and technological parameters of the developed device were determined: l=8 mm, ω=106 rpm. As a result of production tests, it was found that when using the developed device, the daily milk yield of the experimental group of cows exceeded that of the control group by an average of 1.1 times which has made it possible to obtain a supplement of 132.5 kg of milk. Along with this, there was a 0.19 % increase in milk fat content in the experimental group compared to the control group. The number of microorganisms decreased 2.2 times and the number of contaminant particles decreased 4.6 times

27 December 2018 in Food Science and Technology
Verified
Journal Article
Open access
ISI. Shevchenko
I. Shevchenko
EAElchyn Aliiev
Elchyn Aliiev
The aim of the research was to make the mechanical and technological process of calibrating confectionery sunflower seeds with a vibrating sieve more effective by giving reasons for its rational methodical and technological parameters. The study of calibration of confectionery sunflower seeds had two stages: numerical simulation and experimental verification. For the first stage, the physical models for numerical simulation (in the STAR-CCM+ software package) of the movement of seeds with a vibrating sieve were: k-ɛ model of separated flow turbulence, gravity field, Van der Waals real gas model, discrete elements model, multiphase interaction model. The second stage, experimental verification of the models obtained, was carried out on a calibration machine (sizer) OKMF. Sieves of three types were selected: perforated sieves, rod sieves, and precision sieves (produced by laser cutting). The numerical simulation of moving the confectionery sunflower seeds with a vibrating sieve has allowed determining how changes in total concentration and productivity depend on the way of the input of the seeds, the sieve angle, the vibration frequency and vibration amplitude of the sieve. To make the seed separation process effective, the vibrating sieve is to operate with the maximum productivity equal to the seed input (1,202 kg/h), with the maximum total seed concentration (10.83%). Experimental studies of moving the seeds of confectionery sunflower with vibrating sieves of different types (perforated screens, rod sieves, and precision sieves) have allowed establishing how changes in total concentration, productivity, and consumed power of the calibrating machine depend on the seed input, sieve angle, and frequency of vibrations of the sieve. To make the seed separation process effective, the vibrating sieve is to operate with the maximum productivity equal to the seed input (perforated screens – 1.116 kg/h, rod sieves – 1,518 kg/h, precision sieves – 1,781 kg/h), with the following total seed concentrations: perforated sieves – 14.54%, rod sieves – 12.45%, precision sieves – 10.41%, and power P (perforated sieves – 0.24 kW, rod sieves – 0.30 kW, precision sieves – 0.35 kW) consumed by the calibrating machine must be minimum. Precision sieves (produced by laser cutting) have the best characteristics of their performance (q=1781 kg/h) and quality (θ=10.41%). For this, the frequency of their vibrations should be 5.9 Hz, and their angle should be 5°.

10 June 2021 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
APAndriy Paliy
Andriy Paliy
EAElchyn Aliiev
Elchyn Aliiev
ANAlexander Nanka
Alexander Nanka
OBOleksiy Bogomolov
Oleksiy Bogomolov
VBVadim Bredixin
Vadim Bredixin
NGNatalia Grebenik
Natalia Grebenik
Many years of experience in the operation of milking machines show that milking rubber was and remains a short-lived and unreliable link in the technological process of machine milking. During operation, rubber quickly loses its strength and elastic properties, becomes stiff and less elastic, deforms, and changes its shape. The purpose of this study is to identify changes in the technical parameters of milking rubber under industrial conditions in order to establish their impact on the milking process. The obtained results could make it possible to rationally choose the milking rubber for teat cups, which would ensure an effective milking process. During this study’s initial stage, the physical and mechanical condition of milking rubber was experimentally established at steam disinfection and as a result of saturating the article with milk fats. The following stage implied detecting the effect of milking rubber tension in a teat cup on the speed of milking. It was established that milking rubber during operation is actively exposed to milk fat, which leads to the loss of its weight relative to its original value. On day 1,000 of work, the weight loss relative to the initial value (100 g), under the washing regime temperature of 85 °C, 50 °C, 35 °C, and 20 °C, was 1 g, 3.3 g, 5 g, and 4.2 g, respectively. The dependences have been derived for the swell mass of milking rubber M on the temperature of washing solutions T and the duration of operation t as a result of saturation with milk fats. The dependence of milk yield rate V on the tension force of milking rubber F in teat cups has been established. Thus, it was found that when the tension force of milking rubber changes from 25 to 60 N, the difference in the average intensity of milk yield is 0.13 kg/min (10.8 %). Regarding the amount of milk yield at the specified tension, the difference is 0.15 kg (2.5 %). At rubber tension from 60 to 25 N, the average milking time increases by 0.46 min (8.3 %). Thus, it was determined that a milking machine with milking rubber at different tension over a total milking time would unevenly milk different parts of the cow’s udder. The study reported here expands the idea about the technical and manufacturing characteristics of rubber articles, namely changes in them at steam disinfection and as a result of saturation with milk fats