This study addresses the problem of traffic congestion in large cities caused by long-term repairs of underground utility networks. An innovative mobile overpass is considered, which combines the functions of a vehicle and a temporary bridge, allowing passenger cars up to 3.5 t to pass directly over repair trenches without detours. The research focuses on optimizing the placement of overpass supports relative to the trench edge to reduce soil deformation and prevent trench wall instability. A numerical methodology is developed in ANSYS Workbench that integrates finite element analysis of the soil-support system with parametric optimization using the nonlinear Drucker–Prager elastoplastic model. The soil parameters are obtained from oedometer compression tests (KPr-1M) and direct shear tests (PSG-2M) on clayey soils and then used to calibrate the numerical model. The optimization results show that the optimal distance from the trench wall to the overpass support is m, which is 13.5% greater than the initial design value. This modification reduces the maximum horizontal displacement of the trench wall by more than a factor of two and ensures compliance with the displacement criteria. Comparison between experimental and numerical compression curves yields an average deviation of 37.55%, with errors below 5% at higher stress levels, confirming that the Drucker–Prager model is suitable for engineering optimization of mobile overpass support placement on similar soils. The proposed methodology can be applied to the design and verification of temporary bridge systems operating above utility trenches in urban environments.
The study presents an engineering solution for maintaining traffic flow during road and utility operations, such as trench excavation. The analysis of existing organizational and technical approaches, along with global experience in temporary bridge use, showed that most foreign analogs were developed for military purposes and are not fully suitable for urban conditions in Kazakhstan and CIS countries. As an alternative solution, the development of a mobile overpass adapted for operation in dense urban environments is proposed. The present study continues earlier research focused on optimizing the placement of mobile overpass supports while accounting for the nonlinear deformation behavior of the soil foundation. At the previous stage, a rational distance between the supports and the trench edge was substantiated, and horizontal soil deformations were reduced. In the current study, the primary focus is on the design of the undercarriage, which determines the mobility, stability, and operational feasibility of the structure. A morphological analysis and synthesis method is applied to select a rational configuration of the undercarriage. A 3D model and a 1:4 scale test bench were developed, followed by load tests of 50–200 kg. The maximum deflection of −1.19 mm at 200 kg demonstrated an almost linear deformation pattern. The constructed regression model () confirmed the accuracy and reliability of the design. The developed mobile overpass is versatile, cost-effective, and practical, improving the resilience of urban transport infrastructure, reducing traffic congestion during roadworks, and creating a foundation for serial production in Kazakhstan and CIS countries.
This article discusses the relevant problem of ensuring transport connectivity under the conditions of temporal restrictions of the road network, which arise during repair, communal and emergency operations. It is established that the existing organizational and intellectual methods of traffic management do not eliminate physical decrease in road capacity, while construction of stationary structures with different levels is limited by high costs and long terms of implementation. The above substantiates the need for the development of mobile overpasses as adaptive engineering solutions ensuring continuity of the traffic flows. The purpose of the research is to develop a scientifically substantiated theoretical and experimental methodology for designing a mobile overpass as an integrated system “structure-moving load”, taking into account its dynamic behavior. The paper proposes an integrated approach based on the use of physical similarity theory and dimensionless analysis. A differential equation of dynamic bending of a beam on an elastic foundation is formulated taking into account inertia, damping, base reaction and the effect of a moving mass, and then its nondimensionalization is performed to obtain a similarity criteria system. The scientific novelty of the research consists in developing a system of dimensionless criteria to describe the relationship between the structural, dynamic and operational parameters of a mobile overpass, as well as in the formation of a criterion base for large-scale modeling and transfer of the results to full-scale structures. The proposed methodology describes the mobile overpass as an integrated transport-engineering system accounting for the coupled interaction between the deformable structure, moving traffic load, elastic foundation, and damping effects. Experimental verification was performed on a specially designed stand in the scale 1:4. The results obtained showed the quasi-static nature of the structure performance with moderate damping and rigid base. It is established that the distribution of engineering stresses along the span length has a regular character and retains its shape when the load level changes, which confirms fulfillment of similarity conditions. Regression analysis revealed a close to linear dependence of stresses on the load mass with a high degree of confidence . The practical significance of the research consists in creating an engineering method for express design of mobile overpasses, which allows for assessing their stress–strain state, stability and serviceability without expensive full-scale tests. The proposed approach can be used in designing temporary transportation structures under the conditions of urban area, and in operation in areas of road operations and emergency situations.
31 March 2026 in Material and Mechanical Engineering Technology
The article discusses the development and research of a mobile overpass as an engineering solution in the field of mechanical engineering and transport technology. It describes the design features of the overpass: the load-bearing span integrated into a two-axle wheeled chassis, the tensioning mechanism, and the suspension system, which ensure reliability and stability under dynamic loads. The technological advantages of the design are shown: mobility, quick installation without major construction, modularity, and the possibility of repeated use in various operating conditions. Based on preliminary engineering calculations and analysis of transport loads, the strength and operational reliability of the structure when moving passenger cars and light-duty vehicles is justified. The use of reinforced guide elements and a spatial truss scheme minimizes deformation and evenly distributes loads. The economic analysis confirms the efficiency of the proposed overpass's installation and operation, demonstrating a total annual saving exceeding 18 million tenge, primarily through reduced fuel consumption and minimized vehicle idling time. The results of the study confirm the feasibility of introducing mobile overpasses as an effective engineering solution that ensures the maintenance of transport links during major repairs and reconstruction of roads. The design combines manufacturability, mobility, and operational reliability, which opens up prospects for its widespread use in Kazakhstan's transport infrastructure
26 September 2026 in Journal of Transport Engineering, Logistics and Economics
The reliability of automotive driveline components directly affects vehicle safety, maintenance costs, and operational efficiency. Among these components, the cardan transmission (propeller shaft) is subjected to complex dynamic loads, vibrations, and cyclic stresses, making it vulnerable to fatigue-related failures. Conventional maintenance approaches rely on scheduled inspections without considering the individual operating conditions of each vehicle. This study proposes an individual prediction model for cardan transmission failures based on operational parameters and machine learning techniques. The developed methodology integrates vibration characteristics, torque loading, rotational speed, mileage, temperature, and lubrication condition into a predictive algorithm capable of estimating the remaining useful life (RUL) of the transmission. Experimental analysis demonstrates that individualized prediction significantly increases diagnostic accuracy compared with traditional maintenance schedules and enables predictive maintenance strategies.