The large-scale wind energy conversion system (WECS) based on a doubly fed induction generator (DFIG) has gained popularity in recent years because of its various economic and technical merits. The fast integration of WECS with existing power grids has caused negative influence on the stability and reliability of power systems. Grid voltage sags produce a high overcurrent in the DFIG rotor circuit. Such these challenges emphasise the necessity of the low voltage ride through (LVRT) capability of a DFIG for ensuring power grid stability during voltage dips. To deal with these issues simultaneously, this paper aims to obtain the optimal values of injected rotor phase voltage for DFIG and wind turbine pitch angles for all operating wind speeds in order to achieve LVRT capability. Bonobo optimizer (BO) is a new optimization algorithm that is applied to crop the optimum values of injected rotor phase voltage for DFIG and wind turbine pitch angles. These optimal values provide the maximum possible DFIG mechanical power to guarantee rotor and stator currents do not exceed the rated values and also deliver the maximum reactive power for supporting grid voltage during faults. The ideal power curve of a 2.4 MW wind turbine has been estimated to get the allowable maximum wind power for all wind speeds. To validate the results accuracy, the BO results are compared to two other optimization algorithms: particle swarm optimizer and driving training optimizer. Adaptive neuro fuzzy inference system is employed as an adaptive controller for the prediction of the values of rotor voltage and wind turbine pitch angle for any stator voltage dip and any wind speed.
The operation of wind power system at optimum power point is a big challenge particularly under uncertainty of wind speed. As a result, it is necessary to install an effective maximum power point tracking (MPPT) controller for extracting the available maximal power from wind energy conversion system (WECS). Therefore, this paper aims to obtain the optimal values of injected rotor phase voltage for doubly fed induction generator (DFIG) to ensure the extraction of peak power from wind turbine under different wind speeds as well as to get the optimal performance of DFIG. A new metaheuristic optimization approach; Driving Training Algorithm (DTA) is used to crop the optimal DFIG rotor voltages. Three different scenarios are presented to have MPPT, the first one is the MPPT with unity stator power factor, the second one is the MPPT with minimum DFIG losses, and the third scenario is MPPT with minimum rotor current to reduce the rating of rotor inverter. The MATLAB environment is used to simulate and study the proposed controller with 2.4 MW wind turbine. The optimum power curve of wind turbine has been estimated to get the reference values of DFIG mechanical power. The results ensured the significance and robust of the proposed controller to have MPPT under different wind speeds. The DTA results are compared with other two well-known optimization algorithms; water cycle algorithm (WCA) and particle swarm optimizer (PSO) to verify the accuracy of results.
3 July 2018 in Australian Journal of Electrical and Electronics Engineering
The number of bridges, gate drive circuits and dc sources decrease by using asymmetrical is used to solve SHE equations to get the optimal switching angles. Genetic algorithm (GA) is also used to solve these equations to make comparison between Satin bowerbird optimisation (SBO) and GA algorithms. Matlab/Simulink software tool is used to carry out the simulation construction multilevel inverter. The selective harmonic elimination pulse width modulation (SHE-PWM) and sinusoidal pulse width modulation (SPWM) are carried out for a nine levels cascaded H-bridge (CHB) inverter with asymmetrical construction. Comparison between SHE and SPWM is done to get the benefit of SHE over SPWM. The elimination of some lower order harmonics and satisfy fundamental component in output voltage are the major purpose of SHE-PWM. The solving of the non-linear transcendental equations of SHE is the challenge to find out the switching angles, SBO technique.
Multilevel inverters are very important in renewable energy applications. Asymmetrical type of multilevel inverters is used for saving of the number of dc sources, gate drive circuits and bridges. It gives the number of levels for output voltage higher than from symmetrical type. Multi-carrier based sinusoidal pulse width modulation (MCB-SPWM) and the selective harmonic elimination pulse width modulation (SHE-PWM) are commonly types of modulation techniques. The comparison between MCB-SPWM and SHE-PWM is done for a nine levels cascaded H-bridge (CHB) inverter with asymmetrical type to show the advantages of two types of PWM techniques. The difficulty of SHE-PWM is a solution of the non-linear transcendental equations of SHE. To solve this difficulty, Evolutionary algorithms such as genetic algorithm are used to find optimal switching angles. MCB-SPWM and SHE-PWM are performed by MATLAB / SIMULINK software packages.
A fully integrated PHS (personal handy phone system) transceiver achieving -105 dBm sensitivity and +21 dBm output power is presented. The transceiver is implemented in a 0.35 /spl mu/m SiGe BiCMOS process occupying an area of 13 mm/sup 2/ and dissipating 74 mA in receive mode and 280 mA in transmit from a 3 V supply. The receiver is based on a low-IF architecture and does not require any external filters. The TX integrates a linear +21 dBm power amplifier and achieves 5% EVM and -60 dBc ACP. The transceiver integrates a fractional-N synthesizer with <30 /spl mu/s lock time and -120 dBc/Hz phase noise at 600 kHz offset frequency. The base-band interface is at 1.2 MHz, compatible with commercially available PHS base-band chips to create a two chip solution for PHS phones.