Проведенное исследование посвящено актуальным вопросам обеспечения сбалансированности трансформации предприятий в условиях инноваций. Современные тенденции развития компаний требуют от них непрерывности инновационных процессов и модернизации для сохранения уровня конкурентоспособности. Степень инновационности и направленность проектов определяется самой компанией, исходя из ее экономических интересов, однако вопросы, связанные с повышением уровня согласованности протекающих процессов, их промышленной безопасности не являются приоритетными при выборе инновационных проектов. В долгосрочной перспективе такой подход к проектному управлению приводит к снижению уровня живучести и надежности организации, вызывает возникновение новых «узких» мест в развитии, ведет к росту неопределенности и увеличению комплекса рисков за счет промышленных и инвестиционных. Авторами исследованы методологические подходы к оценке сбалансированности инновационного развития при реализации проектного управления в компаниях. На основе чего предложена комплексная оценка сбалансированного устойчивого развития компаний при реализации инновационных проектов и предложен графический инструментарий представления результатов исследования для формирования стратегии управления. Данные предложения могут быть использованы руководителями различных организаций при формировании стратегий развития и реализации проектного управления. Теоретические разработки, рассмотренные в статье, могут быть интересны исследователям, которые занимаются вопросами сбалансированного управления, проблемами устойчивого развития и особенностями инновационных процессов.
A modular computational fluid dynamics (CFD) framework for heat and nonequimolar mass transfer in a thin liquid layer is formulated in ANSYS Fluent using user-defined source terms. The sensible thermal module rewrites the near-wall Fourier heat flux as a volumetric energy source, SE,th = λeff(Tw − T)/(δy hc), where λeff is the local effective thermal conductivity, Tw and T are the boundary and cell temperatures, and δy and hc characterize the wall-adjacent source layer. The mass-transfer module uses the structurally analogous source ṁpc = k0(Y0,b − Y0), with k0 = Dmρ0/(δy hc), and the phase-change energy contribution is SE,pc = −ṁpc hfg. A full-scale gasketed plate heat exchanger with a 3 mm interplate gap was used to verify the single-phase thermal component implemented through source_thermal_energy; mass-transfer, species, transient UDS, and latent-heat source terms were disabled. The thermal CFD calculation predicted cold- and hot-stream outlet temperatures of 338.01 and 350.81 K versus measured values of 338.15 and 349.65 K, corresponding to relative deviations of 0.041% and 0.332%. The experimental comparison therefore verifies the sensible thermal component under single-phase conditions, whereas evaporation, condensation, nonequimolar species transfer, and latent-heat coupling remain outside the experimentally verified scope.
The article presents the results of experimental studies of the velocity of liquid droplets in a chain under the action of centrifugal forces in a uniformly rotating liquid continuous phase. The aim of the work is to study the mutual influence of droplets on each other through the analysis of entrainment, simplified to plane motion. An experimental setup was developed based on a cylindrical vessel with adjustable angular velocity, a droplet-forming device, and stroboscopic photography to record trajectories. The methodology includes phase saturation, adjustment of the dispersed phase flow rate, and two shooting modes to minimize errors. The dependencies of the satellite trail velocity () on the radial distance (R) and the drop frequency (f) were obtained for three liquid systems; based on regression analysis, a generalized formula was proposed, providing satisfactory agreement between the calculated and experimental data (deviation < 10%). The results confirm the increase in with increasing R and f, which allows optimizing the extraction and mass transfer processes in centrifugal devices.