Using methods of pulsed laser ablation from a silicon target in helium (He)-nitrogen (N2) gas mixtures maintained at reduced pressures (0.5–5 Torr), we fabricated substrate-supported silicon (Si) nanocrystal-based films exhibiting a strong photoluminescence (PL) emission, which depended on the He/N2 ratio. We show that, in the case of ablation in pure He gas, Si nanocrystals exhibit PL bands centered in the “red - near infrared” (maximum at 760 nm) and “green” (centered at 550 nm) spectral regions, which can be attributed to quantum-confined excitonic states in small Si nanocrystals and to local electronic states in amorphous silicon suboxide (a-SiOx) coating, respectively, while the addition of N2 leads to the generation of an intense “green-yellow” PL band centered at 580 nm. The origin of the latter band is attributed to a radiative recombination in amorphous oxynitride (a-SiNxOy) coating of Si nanocrystals. PL transients of Si nanocrystals with SiOx and a-SiNxOy coatings demonstrate nonexponential decays in the micro- and submicrosecond time scales with rates depending on nitrogen content in the mixture. After milling by ultrasound and dispersing in water, Si nanocrystals can be used as efficient non-toxic markers for bioimaging, while the observed spectral tailoring effect makes possible an adjustment of the PL emission of such markers to a concrete bioimaging task.
Due to particular physico-chemical characteristics and prominent optical properties, nanostructured germanium (Ge) appears as a promising material for biomedical applications, but its use in biological systems has been limited so far due to the difficulty of preparation of Ge nanostructures in a pure, uncontaminated state. Here, we explored the fabrication of Ge nanoparticles (NPs) using methods of pulsed laser ablation in ambient gas (He or He-N2 mixtures) maintained at low residual pressures (1–5 Torr). We show that the ablated material can be deposited on a substrate (silicon wafer in our case) to form a nanostructured thin film, which can then be ground in ethanol by ultrasound to form a stable suspension of Ge NPs. It was found that these formed NPs have a wide size dispersion, with sizes between a few nm and hundreds of nm, while a subsequent centrifugation step renders possible the selection of one or another NP size fraction. Structural characterization of NPs showed that they are composed of aggregations of Ge crystals, covered by an oxide shell. Solutions of the prepared NPs exhibited largely dominating photoluminescence (PL) around 450 nm, attributed to defects in the germanium oxide shell, while a separated fraction of relatively small (5–10 nm) NPs exhibited a red-shifted PL band around 725 nm under 633 nm excitation, which could be attributed to quantum confinement effects. It was also found that the formed NPs exhibit high absorption in the visible and near-IR spectral ranges and can be strongly heated under photoexcitation in the region of relative tissue transparency, which opens access to phototherapy functionality. Combining imaging and therapy functionalities in the biological transparency window, laser-synthesized Ge NPs present a novel promising object for cancer theranostics.
Erbium upconversion (UC) photoluminescence (PL) from sol-gel derived barium titanate (BaTiO3:Er) xerogel structures fabricated on silicon, glass or fused silica substrates has been studied. Under continuous-wave excitation at 980 nm and nanosecond pulsed excitation at 980 and 1540 nm, the fabricated structures demonstrate room temperature PL with several bands at 410, 523, 546, 658, 800 and 830 nm, corresponding to the 2H9/2 → 4I15/2, 2H11/2 → 4I15/2, 4S3/2 → 4I15/2, 4F9/2→ 4I15/2 and 4I9/2→ 4I15/2 transitions of Er3+ ions. The intensity of erbium UC PL increases when an additional macroporous layer of strontium titanate is used beneath the BaTiO3 xerogel layer. It is also enhanced in BaTiO3 xerogel films codoped with erbium and ytterbium (BaTiO3:(Er,Yb)). For the latter, a redistribution of the intensity of the PL bands is observed depending on the excitation conditions. A multilayer BaTiO3:(Er,Yb)/SiO2 microcavity structure was formed on a fused silica substrate with a cavity mode in the range of 650–680 nm corresponding to one of the UC PL bands of Er3+ ions. The obtained cavity structure annealed at 450 °C provides tuning of the cavity mode by 10 nm in the temperature range from 20 °C to 130 °C. Photonic application of BaTiO3 xerogel structures doped with lanthanides is discussed.
Sol-gel technology has attracted attention in the fabrication of diverse luminescent materials and thin film structures, with forms that range from powders to microcavities. The optical properties of sol-gel-derived structures depend on the sol composition, deposition, and heat treatment conditions, as well as on the film thicknesses and other factors. Investigations on the upconversion luminescence of lanthanides in film structures and materials are also ongoing. In this study, we synthesized three different types of materials and film structures using the same sol, which corresponded to a Ba0.76Er0.04Yb0.20TiO3 xerogel, as follows: (a) the target form, which used the explosive compaction method for sol-gel-derived powder; (b) single-layer spin-on xerogel films annealed at 450 and 800 °C; and (c) microcavities with an undoped SiO2/BaTiO3 Bragg reflector surrounding a Ba0.76Er0.04Yb0.20TiO3 active layer. The BaTiO3:(Er,Yb)/SiO2 microcavity exhibited an enhancement of the upconversion luminescence when compared to the BaTiO3:(Er,Yb) double-layer film fabricated directly on a crystalline silicon substrate. The reflection spectra of the BaTiO3:(Er, Yb)/SiO2 microcavity annealed at 800 °C demonstrated a deviation of the maxima of the reflection within 15% for temperature measurements ranging from 26 to 120 °C. From the analyses of the transmission and reflection spectra, the optical band gap for the indirect optical transition in the single layer of the BaTiO3:(Er,Yb) spin-on film annealed at 450 °C was estimated to be 3.82 eV, while that for the film annealed at 800 °C was approximately 3.87 eV. The optical properties, upconversion luminescence, and potential applications of the BaTiO3:(Er,Yb) sol-gel-derived materials and structures are discussed in this paper.
Nanostructured diamonds hosting optically active paramagnetic color centers (NV, SiV, GeV, etc.) and hyperfine-coupled with them quantum memory 13C nuclear spins situated in diamond lattice are currently of great interest to implement emerging quantum technologies (quantum information processing, quantum sensing and metrology). Current methods of creation such as electronic-nuclear spin systems are inherently probabilistic with respect to mutual location of color center electronic spin and 13C nuclear spins. A new bottom-up approach to fabricate such systems is to synthesize first chemically appropriate diamond-like organic molecules containing desired isotopic constituents in definite positions and then use them as a seed for diamond growth to produce macroscopic diamonds, subsequently creating vacancy-related color centers in them. In particular, diamonds incorporating coupled NV-13C spin systems (quantum registers) with specific mutual arrangements of NV and 13C can be obtained from anisotopic azaadamantane molecule. Here we predict the characteristics of hyperfine interactions (hfi) for the NV-13C systems in diamonds grown from various isotopically substituted azaadamantane molecules differing in 13C position in the seed, as well as the orientation of the NV center in the post-obtained diamond. We used the spatial and hfi data simulated earlier for the H-terminated cluster C510[NV]-H252. The data obtained can be used to identify (and correlate with the seed used) the specific NV-13C spin system by measuring, e.g., the hfi-induced splitting of the mS = ±1 sublevels of the NV center in optically detected magnetic resonance (ODMR) spectra being characteristic for various NV-13C systems.
Single-layer (SLG)/few-layer (FLG) and multilayer graphene (MLG) (>15 layers) samples were obtained using the CVD method on high-textured Cu foil catalysts. In turn, plasma-assisted molecular beam epitaxy was applied to carry out the GaN graphene-assisted growth. A thin AlN layer was used at the initial stage to promote the nucleation process. The effect of graphene defectiveness and thickness on the quality of the GaN epilayers was studied. The bilayer graphene showed the lowest strain and provided optimal conditions for the growth of GaN/AlN. Theoretical studies based on the density functional theory have shown that the energy of interaction between graphene and AlN is almost the same as between graphite sheets (194 mJ/m2). However, the presence of vacancies and other defects as well as compression-induced ripples and nitrogen doping leads to a significant change in this energy.