M. B. Chen

Dr. M. B. Chen


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 April 2019 in Entropy
Verified
Journal Article
Open access
PDF file
QXQiuwei Xing
Qiuwei Xing
HWHaijiang Wang
Haijiang Wang
MCM. B. Chen
M. B. Chen
ZCZhaoyun Chen
Zhaoyun Chen
RLRongbin Li
Rongbin Li
Yong ZhangYong Zhang
Yong Zhang
In this study, we designed and fabricated NbTiAlSiZrNx high-entropy alloy (HEA) films. The parameters of the radio frequency (RF) pulse magnetron sputtering process were fixed to maintain the N2 flux ratio at 0%, 10%, 20%, 30%, 40%, and 50%. Subsequently, NbTiAlSiZrNx HEA films were deposited on the 304 stainless steel (SS) substrate. With an increasing N2 flow rate, the film deposited at a RN of 50% had the highest hardness (12.4 GPa), the highest modulus (169 GPa), a small roughness, and a beautiful color. The thicknesses of the films were gradually reduced from 298.8 nm to 200 nm, and all the thin films were of amorphous structure. The electrochemical corrosion resistance of the film in a 0.5 mol/L H2SO4 solution at room temperature was studied and the characteristics changed. The HEA films prepared at N2 flow rates of 10% and 30% were more prone to corrosion than 304 SS, but the corrosion rate was lower than that of 304 SS. NbTiAlSiZrNx HEA films prepared at N2 flow rates of 20%, 40%, and 50% were more corrosion-resistant than 304 SS. In addition, the passivation stability of the NbTiAlSiZrNx HEA was worse than that of 304 SS. Altogether, these results show that pitting corrosion occurred on NbTiAlSiZrNx HEA films.

10 January 2017 in Metals
Verified
Journal Article
Open access
PDF file
SXSongqin Xia
Songqin Xia
XYXiao Yang
Xiao Yang
MCM. B. Chen
M. B. Chen
Tengfei YangTengfei Yang
Tengfei Yang
Yong ZhangYong Zhang
Yong Zhang
In this study, five-component high-entropy alloys (HEAs) AlxCrFeNiV (where x denotes the molar ratio, x = 0, 0.1, 0.3, 0.5, 0.75, 1, and 1.5) were prepared using an arc-melting furnace. The effects of the addition of the Al on the crystal structures were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Also, two non-equiatomic ratio HEAs, AlxCrFeNiV (x = 0.3, and 0.5), were systematically studied through the use of various characterization methods in the as-cast state. The Al0.3CrFeNiV alloy displayed typical duplex body-centered cubic (BCC) structures, including disordered BCC (A2), and NiAl-type ordered BCC (B2) phases. Meanwhile, in regard to the Al0.5CrFeNiV alloy, this alloy was found to contain an unknown phase which was enriched in Cr and V, as well as the coherent A2/B2 phases. Both of these alloys displayed very high yield and fracture strengths. However, their compression fracture strains were approximately 10%. Also, the fracture surfaces showed mainly cleavage fracture modes.

1 November 2012
Verified
Journal Article
Closed access
MCM. B. Chen
M. B. Chen
WLWen-Chang Liu
Wen-Chang Liu
JLJian Li
Jian Li
XMXiao-Yi Ma
Xiao-Yi Ma
WMWen Ma
Wen Ma
QMQi-Sing Man
Qi-Sing Man

1 May 2013
Verified
Journal Article
Closed access
MCM. B. Chen
M. B. Chen
WLWen-Chang Liu
Wen-Chang Liu
XMXiao-Yi Ma
Xiao-Yi Ma
JLJian Li
Jian Li
QYQing-Xiang Yang
Qing-Xiang Yang
YZY M Zhao
Y M Zhao

1 September 2013
Verified
Journal Article
Closed access
MCM. B. Chen
M. B. Chen
MMMin Ma
Min Ma
QYQing-Xiang Yang
Qing-Xiang Yang
SWShan Wang
Shan Wang
WLWen-Chang Liu
Wen-Chang Liu
YZYing-Mei Zhao
Ying-Mei Zhao