Native collagen fibrils (CF) were successfully extracted from bovine tendons using two different methods: modified acid-solubilized extraction for A-CF and pepsin-aided method for P-CF. The yields of A-CF and P-CF were up to 64.91% (±1.07% SD) and 56.78% (±1.22% SD) (dry weight basis), respectively. The analyses of both amino acid composition and sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) confirmed that A-CF and P-CF were type I collagen fibrils. Both A-CF and P-CF retained the intact crystallinity and integrity of type I collagen’s natural structure by FTIR spectra, circular dichroism spectroscopy (CD) and X-ray diffraction detection. The aggregation structures of A-CF and P-CF were displayed by UV–Vis. However, A-CF showed more intact aggregation structure than P-CF. Microstructure and D-periodicities of A-CF and P-CF were observed (SEM and TEM). The diameters of A-CF and P-CF are about 386 and 282 nm, respectively. Although both A-CF and P-CF were theoretically concordant with the Schmitt hypothesis, A-CF was of evener thickness and higher integrity in terms of aggregation structure than P-CF. Modified acid-solubilized method provides a potential non-enzyme alternative to extract native collagen fibrils with uniform thickness and integral aggregation structure.

Silk fibroin (SF) is a natural protein polymer and promising biomaterial. Chemical modifications have attracted growing interest in expanding SF applications. However, the majority of amino acid residues in SF are non-reactive and most of the reactive ones are in the crystalline region. Herein, a modification was conducted to investigate the possibility of direct modification on the surface of natural SF by a reagent with a mild reactivity, the type and quantity of the residues involved in the reactions, and the structural changes upon modification. Infrared spectrum, ¹H NMR, titration and amino acid analyses, X-ray diffraction, and hemolysis test were used to analyze the materials. The results showed that sulfonic acid groups were grafted onto SF and the reaction occurred mainly at serine residues through hydroxyl groups. In total, 0.0958 mmol/g of residues participated in the modification with a modification efficiency of 7.6%. Moreover, the crystallinity and the content of β-sheet structure in SF increased upon modification. The modified material had good blood-compatibility. In conclusion, surface modification on native SF through serine residues was practicable and had the advantage of increased β-sheet structure. This will provide an alternative way for the modification of fibroin for the desired application in the biomedical field.

Poly (ε-caprolactone) (PCL) and chitosan (CS) are widely used as biodegradable and biocompatible polymers with desirable properties for tissue engineering applications. Composite membranes (CS–PCL) with various blend ratios (CS:PCL, w/w) of 0:100, 5:95, 10:90, 15:85, 20:80, and 100:0 were successfully prepared by lyophilization. The thermal stabilities of the CS–PCL membranes were systematically characterized by thermogravimetric analysis (TG), dynamic thermogravimetry (DTG), and differential scanning calorimetry (DSC). It was shown that the blend ratio of PCL and CS had a significant effect on the thermal stability, hydrophilicity, and dynamic mechanical viscoelasticity of the CS–PCL membranes. All the samples in the experimental range exhibited high elasticity at low temperature and high viscosity at high temperatures by dynamic mechanical thermal analysis (DMTA). The performances of the CS–PCL membranes were at optimum levels when the blend ratio (w/w) was 10:90. The glass transition temperature of the CS–PCL membranes increased from 64.8 °C to 76.6 °C compared to that of the pure PCL, and the initial thermal decomposition temperature reached 86.7 °C. The crystallinity and porosity went up to 29.97% and 85.61%, respectively, while the tensile strength and elongation at the breakage were 20.036 MPa and 198.72%, respectively. Therefore, the 10:90 (w/w) blend ratio of CS/PCL is recommended to prepare CS–PCL membranes for tissue engineering applications.

A PEG-based FSPCM was prepared in water via a simple method, using mannitol as supporting material through intermolecular hydrogen bonding. This FSPCM has high latent heat values and can be chemically recycled with recycling rates over 90%.

The new rigid planar ligand 2,5-bis(3-(pyridine-4-yl)phenyl)thiazolo[5,4-d]thiazole (BPPT) has been synthesized, which is an excellent building block for assembling coordination polymer. Under solvothermal reaction conditions, cadmium ion with BPPT in the presence of various carboxylic acids including (1,1′-biphenyl)-4,4′-dicarboxylic acid (BPDC), isophthalic acid (IP), and benzene-1,3,5-tricarboxylic acid (BTC) gave rise to three coordination complexes, viz, [Cd(BPPT)(BPDA)](BPPT)n (1), [Cd(BPPT) (IP)] (CH₃OH) (2), and [Cd₃(BPPT)₃(BTC)₂(H₂O)₂] (3). The structures of 1, 2, and 3 were characterized by single crystal X-ray diffraction. The IR spectra as well as thermogravimetric and luminescence properties were also investigated. Complex 1 is a two-dimensional (2D) network and further stretched to a 3D supramolecular structure through π–π stacking interaction. The complexes 2 and 3 show 3D framework. The complexes 1, 2, and 3 exhibited luminescence property at room temperature.

A novel 36-metallacrown-6 complex [CuL(N(CN)₂)(PF₆)]₆∙0.5H₂O 1 was achieved using a tridendate ligand, 1,4,7-triisopropyl-1,4,7-triazacyclononane (L), and a flexible ligand, dicyanamide in MeOH. The μ_1,5 bridging models of the dicyanamide ligand linked the macrocycle to form in a specific size with the chair conformation. The anion was important to form this 36-metallacrown-6 complex, as change was obtained with the larger anion BPh₄⁻, binuclear copper compound 2. The magnetic property indicates that slightly ferromagnetic interactions resulted from a superexchange mechanism. DNA binding properties were also studied. UV and fluorescence spectra showed that complex 1 could bind with DNA.