The production of municipal solid waste incineration bottom ash (MSWIBA) is substantial and has the potential to replace cement, despite challenges such as complex composition, uneven particle size distribution, and low reactivity. This paper employs sodium silicate activation of MSWIBA composite Ground-granulated Blast Furnace slag (GGBS) to improve the reactivity in preparing composite cementitious materials. It explores the hydration performance of the composite cementitious materials using isothermal calorimetric analysis, Fourier-transform infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM tests. SEM tests were used to explore the hydration properties of the composite gelling. The results show that with an increase in MSWIBA doping, the porosity between the materials increased, the degree of hydration decreased, and the compressive strength decreased. When the sodium silicate concentration increased from 25% to 35%, excessive alkaline material occurred, impacting the alkaline effect. This inhibited particle hydration, leading to a decrease in the degree of hydration and, consequently, the compressive strength. The exothermic process of hydration can be divided into five main stages; quartz and calcite did not fully participate in the hydration reaction, while aluminum did. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM all indicate the presence of alumosilicate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

The production of municipal solid waste incineration bottom ash (MSWIBA) is very massive and has the potential to replace cement despite the problems of complex composition, uneven particle size distribution, and low reactivity. This paper adopts sodium silicate activation of MSWIBA-slag to improve the reactivity to prepare composite cementitious materials. It explores the hydration performance study of the composite cementitious materials by isothermal calorimetric analysis, Fourier Transform Infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM/EDS tests. SEM/EDS tests will be used to explore the hydration properties of the composite gelling. The results showed that with the increase of MSWIBA doping, the porosity between the materials increased, the degree of Hydration decreased, and the compressive strength decreased with the rise of MSWIBA. When sodium silicate increased from 25% to 35%, too much alkaline material occurred over the alkaline effect, which inhibited the Hydration of the particles, and the degree of hydration reaction decreased, and the compressive strength decreased accordingly; the exothermic process of Hydration can be mainly divided into five stages, quartz and calcite did not participate in the hydration reaction completely, and sexual aluminum participated in the hydration reaction. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM-EDS all indicate the presence of silica-aluminate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

The artificial ground freezing (AGF) technique is widely used in the construction of subway cross passages due to its advantages of good water sealing, strong adaptability, and minimal environmental impact. However, groundwater seepage adversely affects the formation of the frozen wall. The functional relationship between the content of unfrozen water and the temperature in saturated sandy gravel was obtained using frequency domain reflectometry (FDR). Based on the theories of heat transfer and seepage in porous media, a coupled hydrothermal mathematical model of saturated ground considering phase change was established. This model was verified using results from a model test and a freezing project for a subway cross passage. Building on this, the influence of seepage velocity on the formation and closure time of the frozen wall was studied, and prediction formulas for closure times under different seepage velocities were proposed. The results demonstrate the effectiveness of the VG–Clapeyron model in predicting the unfrozen water content in saturated sandy gravel. Groundwater seepage is the core factor affecting the formation of the frozen wall. As seepage velocity increases, closure times for both the cross passage and the pump room are significantly delayed, and the difference between their respective closure times increases. The upstream sidewall is the weak link in frozen wall expansion under seepage conditions. Monitoring of the temperature field in this area should be strengthened to track the formation of the frozen wall.

Post-installed rebars are extensively used in the strengthening and rehabilitation of concrete structures, where compressive stresses in the anchorage zone provide transverse pressure and significantly affect bond behavior. However, it remains unclear how different transverse pressure conditions, particularly one-way and two-way transverse pressure, influence the bonding behavior of post-installed rebars and how their effects differ. To address this gap, this study investigates the effects of one-way and two-way transverse pressure on the bond mechanism and failure mode of post-installed rebars. To achieve this, 22 pull-out tests were carried out under two transverse pressure configurations, namely one-way and two-way transverse pressure, with pressure levels ranging from 0 to 12 MPa. The results show that, without confinement, concrete splitting was the dominant failure mode, whereas under transverse pressure, failure shifted to adhesive failure or adhesive–rebar interface failure. Transverse pressure significantly improved bond strength, with maximum increases of 49.9% under one-way transverse pressure and 82.9% under two-way transverse pressure. Both the transverse pressure configuration and pressure level had a significant influence on failure evolution and bond performance. In general, increasing the pressure level enhanced the interfacial bonding capacity; however, one-way transverse pressure tended to induce stress concentration in the adhesive layer, thereby promoting adhesive-related failure. These findings clarify the role of transverse pressure conditions in the anchorage behavior of post-installed rebars and provide a basis for the design and analysis of post-installed rebar anchorage systems.