Drilling tool attitude parameters are crucial for achieving precise directional drilling and trajectory control. Navigation systems based on redundant micro-electro-mechanical systems inertial measurement units (MEMS-IMU) significantly improve the reliability and accuracy of drilling tool attitude measurements. To achieve redundant arrangement of MEMS-IMUs, this paper proposes uniformly arranging MEMS-IMUs on a hollow hexagonal prism carrier, taking into account the actual structure of the drilling tool. However, under dynamic conditions, when updating drilling tool attitude using the strapdown inertial navigation system (SINS), the nonlinear errors of the MEMS-IMU accumulate over time, leading to distortion in the attitude calculation results. Therefore, this paper proposes a composite inertial measurement unit (CIMU) attitude measurement method. A virtual inertial measurement unit (VIMU) is generated through multi-IMU data fusion. Furthermore, the geometric constraints between each IMU and the VIMU, combined with Kalman filtering, are used to achieve real-time suppression of attitude errors, thereby improving the accuracy of the drilling tool attitude calculation results. Experimental results show that, compared with conventional data fusion methods, the CIMU algorithm reduces the overall drilling tool attitude error level by 40–70%.
The bent sub is a main deflection component in the near-bit assembly of small-diameter push-the-bit guided coring tools, and its parameters affect build-up capability and local structural response. Existing studies mainly focus on conventional rotary steerable drilling systems, whereas slim-hole constraints, including narrow annular clearance and cross-sectional weakening induced by internal coring channels, remain insufficiently considered. To address this problem, a static bending model of the near-bit section was established based on Euler–Bernoulli beam theory. Channel-induced cross-sectional weakening was represented using the actual concentric annular geometry of the primary load-bearing outer tube, and the bent-sub initial curvature, dual push-the-bit loads, axial weight on bit, and borehole-wall contact and friction effects were incorporated. The build-up rate (BUR), maximum equivalent stress, and maximum curvature served as response indicators. A control-variable approach was used to analyze the bent-sub length Lb, bend angle γ, and distance from the bit Db. The results showed that Db had the strongest effect on BUR, and all parameters exhibited a trade-off between steering performance and structural safety. Increasing Lb from 0.30 m to 0.80 m reduced BUR from 12.65°/30 m to 9.79°/30 m, whereas increasing γ from 0.5° to 2.5° increased BUR from 4.12°/30 m to 10.70°/30 m. Considering structural constraints and normalized BUR retention, the recommended engineering ranges are Lb = 0.65–0.80 m, γ = 1.3°–1.9°, and Db = 0.50–0.70 m.
In directional coring drilling, toolface adjustment is performed during drilling interruption by rotating the drill string through the top drive. Because the bottom-hole toolface angle cannot be transmitted to the surface in real time, a dynamic prediction model is required to guide toolface control. Existing flexible drill string models, however, generally neglect the nonlinear wellbore friction caused by stick–slip motion, reducing prediction accuracy. To address this issue, a distributed-parameter torsional dynamic model is established and discretized into a multi-degree-of-freedom system. A friction-state-based prediction–correction iterative algorithm is proposed to resolve the strong coupling between wellbore friction and system dynamics. At each time step, the sticking or slipping state is identified from the predicted motion, and the wellbore friction torque is iteratively updated until the friction state and dynamic equilibrium simultaneously converge, enabling accurate prediction of the drill bit toolface angle. Simulation results show that the proposed model captures the key dynamic characteristics of toolface adjustment. Under typical operating conditions, the drill bit start-up delay is 3.53 s, the peak angular velocity reaches 1.73°/s, and the peak transmitted torque is 2.28 kN·m. After the top drive stops, the drill bit continues rotating because of inertia, resulting in a 2.12° toolface overshoot and an angular lag rate of 21.2%. In addition, the effects of weight on bit, top-drive speed, and equivalent damping on toolface adjustment are quantified, providing guidance for parameter optimization. The proposed method provides a theoretical basis for toolface prediction and control in intelligent directional coring drilling.