Rajamurugan G

Dr. Rajamurugan G

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2020 in Materials Research Express
Verified
Journal Article
Open access
SKS M Vinu Kumar
S M Vinu Kumar
KKK L Senthil Kumar
K L Senthil Kumar
HJH Siddhi Jailani
H Siddhi Jailani
RGRajamurugan G
Rajamurugan G
In this current investigation, alkali and Trimethoxymethylsilane treated custom made (irregular type) basket woven fabric at different weight percentages (0, 25, 35 and 45 wt.% and named as Pure epoxy, 25 FE, 35 FE, and 45 FE respectively) were reinforced with epoxy resin to develop flax/epoxy composites and tested for mechanical, dynamic mechanical, and sound absorption properties as per ASTM standards. Mechanical results revealed that, amongst the composites, 45 FE showed highest tensile strength, flexural strength, Impact strength and Shore D hardness of 91.07 MPa, 109.5 MPa, 295.65 J m−1, and 85.23 respectively, whereas ILSS property did not shows much appreciable progress even at high fiber loadings. Dynamic mechanical analysis (DMA) tests were conducted for five different frequencies (0.5, 1, 2, 5, and 10 Hz) at varying temperature and properties such as storage modulus (E′), loss modulus (E″), and damping (tanδcurve) were evaluated. DMA properties of the composites have found to be improved after reinforced with the treated flax fabric. Effectiveness coefficient (C) confirms that 45FE composites exhibited better strong fiber-matrix interface and shows good agreement with cole-cole plot analysis. Sound absorption performance of the composites were determined in terms of sound absorption coefficient (SAC) using Impedance tube system for the frequency range 0–6400 Hz. Results indicated that flax-epoxy composites exhibit better sound absorption properties at medium and higher frequency levels. SEM analysis was carried out to understand the cause of failure in mechanically fractured composites. Moreover, morphologies of the fibers were also studied by XRD technique.

29 October 2019 in Journal of Industrial Textiles
Verified
Journal Article
Closed access
PDF file
PKPrabu Krishnasamy
Prabu Krishnasamy
RGRajamurugan G
Rajamurugan G
MTM Thirumurugan
M Thirumurugan
Adding different reinforcements to the polymer composite is gaining more importance in the manufacturing industries because of their variation in mechanical properties. To satisfy modern industrial requirements, the mono-fiber polymer composites are substituted by hybrid composites in civil and automotive applications. The present work is to develop and investigate the hybrid composite behavior reinforced with AISI 304 (500 µm) wire mesh and jute fiber with epoxy LY556 resin. To analyze the mechanical properties of hybrid composites, two different orientations (45° and 90°) of wire mesh are selected and stacked with jute fiber by hand lay-up method. The wire mesh composite or hybrid composite is subjected to mechanical characterization like tensile, flexural, impact, and interlaminar. Subsequently, the viscoelastic behavior of the wire mesh composite is observed in terms of storage modulus (E′), loss modulus (E″), and damping factor (tan δ) by the dynamic mechanical analyzer (DMS 6100). The fractured surface microstructure of the wire mesh composite is analyzed by scanning electron microscope. The 45° oriented wire mesh composite sample shows better mechanical properties in ultimate tensile strength (20.55 MPa), flexural strength (0.145 kN), percentage of elongation (2.83%), and interlaminar strength (0.120 kN). At the transition region, the peak energy absorption of 0.622 is observed in the 90° oriented wire mesh composite sample at 0.5 Hz frequency.

6 November 2020 in Journal of Natural Fibers
Verified
Journal Article
Closed access
PKPrabu Krishnasamy
Prabu Krishnasamy
RGRajamurugan G
Rajamurugan G
SAS Aravindraj
S Aravindraj
PSP Edwin Sudhagar
P Edwin Sudhagar
These articles presents an experimental investigation on mechanical, vibration, and wear behavior of (aloevera/flax/hemp/wire mesh/BaSO4) laminated composite. The mechanical characterization was performed with ASTM standard specimens. The free vibration performance was analyzed under two clamping conditions and boundary conditions (clamp-clamp & clamp-free). The wear test trails were accomplished using a pin on disc at different process parameters like sliding speed (3–5 m/s), sliding distance (1000 m) and applied load (10–30 N) under sliding dry environment at room temperature of 28 ± 5◦C. The scanning electron microscopy was used to examine the interaction between the matrix and reinforcement interface after the failure. The experimental results revealed that the addition of wire mesh and BaSO4 filler in the fabricated composite Aleovera+Hemp+Wiremesh+Flax+Aleovera+BaSO4 composite (C4) increased the tensile strength by 8.68% compared to Aleovera+Hemp+Wire mesh+Flax+ Aleovera (C3) composite and it also depicts that the addition of wire mesh and BaSO4 as reinforcement has improved 5.42% of flexural strength compare to Aleovera+Hemp+Flax+Aleovera+BaSO4 composite (C2). The addition of BaSO4 improved the hardness in both C2 and C4 composites. The 5% addition of BaSO4 enhanced the natural frequency of the composites. Among the composites, the C4 has shown the highest coefficient of friction during the experimental trials.

22 June 2020 in Journal of Industrial Textiles
Verified
Journal Article
Closed access
PDF file
PKPrabu Krishnasamy
Prabu Krishnasamy
RGRajamurugan G
Rajamurugan G
MTM Thirumurugan
M Thirumurugan
This work was investigated that the effect of aluminium (Al) and copper (Cu) wire mesh embedded as a structural reinforcement on jute epoxy hybrid composite. The hybrid composites were prepared by epoxy LY556 with HY951 hardener as a matrix; jute and wire mesh as reinforcements using the compression molding technique. In hybrid composites, the aluminium wire mesh (AWM) and copper wire mesh (CWM) were embedded as 45° & 90° orientation to the jute fiber (AWM45/90 and CWM45/90). The performance of the fabricated hybrid composites was studied by conducting various mechanical, thermal, and dynamic characterizations. The test results were shown that the tensile strength of the fabricated composite was improved by 14.12% in AWM45 and 9.28% in CWM45 compared to AWM90 and CWM90 composites respectively. The TGA result expressed that the thermal stability of the CWM45 composite was enhanced with the residue of 18.33% at 800 °C due to the influence of Cu-wire mesh. In the transition region, the 45° oriented wire mesh improved the loss modulus (E″) peaks about 31.74% in CWM and 11.49% in AWM composite to 90° oriented mesh.

29 January 2020 in Bulletin of Materials Science
Verified
Journal Article
Closed access
PDF file
MAM Arulmurugan
M Arulmurugan
ASA S Selvakumar
A S Selvakumar
KPKrishnasamy Prabu
Krishnasamy Prabu
RGRajamurugan G
Rajamurugan G

4 March 2022 in Journal of Adhesion Science and Technology
Verified
Journal Article
Closed access
KUK. N. Uday
K. N. Uday
RGRajamurugan G
Rajamurugan G
Friction stir welding (FSW) is gaining attention over fusion welding is due to exceptional advantages. The advantages in FSW are superior joint properties, less preparation time, fumeless. FSW welding is widely employed in the automotive and aerospace sectors to join similar and dissimilar aluminium components. Many research articles have published particle reinforced Aluminium composite (AMC) FSW welding and reported improvement in mechanical properties. The paper focuses on the parameters used during welding to obtain good weld quality. The FSW joint efficiency of (AMC) varies between 80 and 95 percent, and joint efficiency is obtained by selecting the optimal combination of tool rotation speed, welding speed, and applied axial load. The tool rotation speed varies between 600 and 1200 rpm, with a 30–110 mm/min welding speed for uniform grain size in the joint using moderate axial loads. The tool profile and process parameters significantly impact welded joints' hardness and tensile behavior. The paper outlines the FSW process, operating ranges, and type of tools been used, which may be helpful for future research in the domain.