Photopharmacology is a field of medicine and pharmacology that uses light to selectively activate or deactivate pharmaceutical agents. This approach significantly enhances and localizes the drug action and, therefore, reduces its side effects. Apart from the bioactive moiety, any photopharmacological compound should contain a photoactive group that must absorb light at the desired wavelength and reorganize the molecular structure after photoactivation. The design of an effective photopharmacological compound requires careful tuning of physical, chemical, and biological properties. The present review summarizes and analyzes the main approaches to the molecular design of photopharmacological drugs based on azobenzene or azoheteroarenes. The main ideas and methods used for tuning spectral and photochemical properties of compounds of this class are discussed. A comparative analysis of main computational methods for theirin silicoscreening is carried out; the most common approaches to the synthesis of azobenzenes and azoheteroarenes derivatives are systematized. Special attention is given to the methods and approaches that are specific to the molecular design of photopharmacological compounds with required physicochemical and photochemical properties.The bibliography includes 212 references.
Membrane potential is a fundamental property of biological cells. Changes in membrane potential characterize a vast number of vital biological processes, such as the activity of neurons and cardiomyocytes, tumorogenesis, cell-cycle progression, etc. A common strategy to record membrane potential changes that occur in the process of interest is to utilize organic dyes or genetically-encoded voltage indicators with voltage-dependent fluorescence. Sensors are introduced into target cells, and alterations of fluorescence intensity are recorded with optical methods. Techniques that allow recording relative changes of membrane potential and do not take into account fluorescence alterations due to factors other than membrane voltage are already widely used in modern biological and biomedical studies. Such techniques have been reviewed previously in many works. However, in order to investigate a number of processes, especially long-term processes, the measured signal must be corrected to exclude the contribution from voltage-independent factors or even absolute values of cell membrane potential have to be evaluated. Techniques that enable such measurements are the subject of this review.
A typical feature of proteins from the rhodopsin family is the sensitivity of their absorption band maximum to protein amino acid composition. For this reason, studies of these proteins often require methodologies that determine spectral shift caused by amino acid substitutions. Generally, quantum mechanics/molecular mechanics models allow for the calculation of a substitution-induced spectral shift with high accuracy, but their application is not always easy and requires special knowledge. In the present study, we propose simple models that allow us to estimate the direct effect of a charged or polar residue substitution without extensive calculations using only rhodopsin three-dimensional structure and plots or tables that are provided in this article. The models are based on absorption maximum values calculated at the SORCI+Q level of theory for cis- and trans-forms of retinal protonated Schiff base in an external electrostatic field of charges and dipoles. Each value corresponds to a certain position of a charged or polar residue relative to the retinal chromophore. The proposed approach was evaluated against an example set consisting of twelve bovine rhodopsin and sodium pumping rhodopsin mutants. The limits of the applicability of the models are also discussed. The results of our study can be useful for the interpretation of experimental data and for the rational design of rhodopsins with required spectral properties.
Fluorescent isocoumarin‐fused cycloalkynes, which are reactive in SPAAC and give fluorescent triazoles regardless of the azide nature, have been developed. The key structural feature that converts the non‐fluorescent cycloalkyne/triazole pair to its fluorescent counterpart is the pi‐acceptor group (COOMe, CN) at the C6 position of the isocoumarin ring. The design of the fluorescent cycloalkyne/triazole pairs is based on the theoretical study of the S1 state deactivation mechanism of the non‐fluorescent isocoumarin‐fused cycloalkyne IC9O using multi‐configurational ab initio and DFT methodologies. The calculations revealed that deactivation proceeds through the electrocyclic ring opening of the α‐pyrone cycle and is accompanied by a redistribution of electron density in the fused benzene ring. We proposed that the S1 excited state deactivation barrier could be increased by introducing a pi‐acceptor group into a position that is in direct conjugation with the formed C=O group and has a reduced electron density in the transition state. As a proof of concept, we designed and synthesized two fluorescent isocoumarin‐fused cycloalkynes IC9O‐COOMe and IC9O‐CN bearing pi‐acceptors at the C6 position. The importance of the nature of a pi‐acceptor group was shown by the example of much less fluorescent CF3‐substituted cycloalkyne IC9O‐CF3.
17 July 2020 in Physical Chemistry Chemical Physics
Quantum mechanics/molecular mechanics (QM/MM) models are a widely used tool to obtain detailed insight into the properties and functioning of proteins. The outcome of QM/MM studies heavily depends on the quality of the applied QM/MM model. Prediction and right placement of internal water molecules in protein cavities is one of the critical parts of any QM/MM model construction. Herein, we performed a systematic study of four protein hydration algorithms. We tested these algorithms for their ability to predict X-ray-resolved water molecules for a set of membrane photosensitive rhodopsin proteins, as well as the influence of the applied water placement algorithms on the QM/MM calculated absorption maxima (λmax) of these proteins. We used 49 rhodopsins and their intermediates with available X-ray structures as the test set. We found that a proper choice of hydration algorithms and setups is needed to predict functionally important water molecules in the chromophore-binding cavity of rhodopsins, such as the water cluster in the N–H region of bacteriorhodopsin or two water molecules in the binding pocket of bovine visual rhodopsin. The QM/MM calculated λmax of rhodopsins is also quite sensitive to the applied protein hydration protocols. The best methodology allows obtaining an 18.0 nm average value for the absolute deviation of the calculated λmax from the experimental λmax. Although the major effect of water molecules on λmax originates from the water molecules located in the binding pocket, the water molecules outside the binding pocket also affect the calculated λmax mainly by causing a reorganization of the protein structure. The results reported in this study can be used for the evaluation and further development of hydration methodologies, in general, and rhodopsin QM/MM models, in particular.
Fluorescence of the vast majority of natural opsin-based photoactive proteins is extremely low, in accordance with their functions that depend on efficient transduction of absorbed light energy. However, several recently proposed classes of engineered rhodopsins with enhanced fluorescence, along with the discovery of a new natural highly fluorescent rhodopsin, NeoR, opened a way to exploit these transmembrane proteins as fluorescent sensors and draw more attention to studies on this untypical rhodopsin property. Here, we review the available data on the fluorescence of the retinal chromophore in microbial and animal rhodopsins and their photocycle intermediates, as well as different isomers of the protonated retinal Schiff base in various solvents and the gas phase.