A novel flexible thermocouple film sensor on a polyimide substrate is proposed that is simple and flexible for monitoring the respiratory signal. Several thermocouples were connected in series and patterned on the polyimide substrate, and each one is formed by copper and a constant line connected to each other at two nodes. The respiratory signal was measured by the output voltage, which resulted from the temperature difference between the hot and cold junctions. The sensors were fabricated with surface-microfabrication technology with three sputtering steps. The measurement results showed that the peak voltage decreased by 90% in the case of apnea compared with normal breathing. The sensor has potential application for wearable detection of sleep apnea hypopnea syndrome (OSAHS).
This paper describes the design and characteristics of a three-chamber electromagnetic-driven peristaltic micropump based on 3D-printing technology. The micropump is composed of an NdFeB permanent magnet, a polydimethylsiloxane (PDMS) film, a 3D-printing pump body, bolts, electromagnets and a cantilever valve. Through simulation analysis and experiments using a single chamber and three chambers, valved and valveless, as well as different starting modes, the results were optimized. Finally, it is concluded that the performance of the three-chamber valved model is optimal under synchronous starting conditions. The measurement results show that the maximum output flow and back pressure of the 5 V, 0.3 A drive source are 2407.2 μL/min and 1127 Pa, respectively. The maximum specific flow and back pressure of the micropump system are 534.9 μL/min∙W and 250.4 Pa/W, respectively.
6 May 2024 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
The effect of aerodynamic noise from high-speed trains on residents living near railway lines is a critical issue. The pantograph cavity is considered to be a major source of aerodynamic noise. To address this problem, this study proposes the application of jetting at the leading edge of the cavity, directly targeting noise reduction at its source. The large eddy simulation approach is used for flow calculations, and the Ffowcs Williams and Hawkings aeroacoustic analogy is adopted for far-field acoustic predictions. Orthogonal designs and the backpropagation algorithm optimized by the genetic algorithm (BP-GA) is used to explore the effects of jetting factors on noise and identify the optimal parameters. Orthogonal design analysis shows that the most influential among the factors is jet orifice diameter, followed by jet velocity and jet angle. The use of the BP-GA algorithm for optimization reveals that the optimal jet parameters are jet velocity of 118.28 m/s, jet angle of 3.17°, and jet orifice diameter of 76.74 mm. The algorithm predicts a minimum noise level of 91.04 dB, which is close to the simulated noise level of 90.74 dB. The jetting process achieves a maximum noise reduction of 4 dB. Results demonstrate that the proposed method for cavity leading edge jetting effectively reduces turbulent kinetic energy and horseshoe-shaped vortices in the cavity, leading to noise reduction. This method also minimizes the effects of aerodynamic noise on distant areas, such as waiting areas and residential buildings. This work provides a theoretical basis for increasing high-speed train speeds.
Compared with the standard extraction interface circuit (SEH), the harvested energy and harvested power of synchronized switching harvesting interface circuits (SSHI) and synchronous charge extraction interface circuit (SECE) cannot improve more effectively. This paper proposes a Bias-Voltage-SSHI Interface Circuit (BV-SSHI), consisting of a single peak voltage detection switch and a rectifier, to solve this problem. The proposed BV-SSHI improves the output voltage by biasing the voltage of the piezoelectric energy harvester and obtains similar harvested power as SSHI. Simulation results show that the BV-SSHI can obtain more harvested energy and harvested power than SEH under weak, medium, and strong coupling systems. Results show that the higher harvester's voltage and the larger phase difference cause the electrical restoring force (χV) to significantly weaken the vibration displacement, especially under strong coupling systems. Thus, the gain effect of the SSHI and SECE is weakened. The experimental results of the medium coupling systems show that the BV-SSHI can obtain 247.2% harvested energy and 121.2% maximum harvested power compared with SEH. The BV-SSHI can achieve at least 142.4% harvested energy and 100.3% maximum harvested power compared with what SSHI and SECE can achieve.
10 June 2025 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
With the continuous increase in operating speeds of high-speed trains, aerodynamic noise generation in the pantograph cavity region has emerged as a critical challenge in railway engineering. To address this issue, this study proposes an innovative hybrid flow control strategy combining an active leading-edge jet with vortex generators at the cavity base. Through synchronized implementation of large eddy simulation (LES) for turbulent flow resolution and the Ffowcs-Williams-Hawkings (FW-H) acoustic analogy for noise propagation modeling, this paper systematically investigated the noise suppression mechanisms induced by jet parameter optimization. Numerical results demonstrate that this synergistic control approach achieves broadband noise reduction across monitoring positions. At 400 km/h operation speed, the proposed configuration yields average sound pressure level (SPL) reductions of 2.96 dB, 3.05 dB, and 3.00 dB at 7.5 m, 12.5 m, and 25 m observation points, respectively. Furthermore, parametric studies reveal that jet orifice contraction angle optimization plays a important role, with the 15° configuration exhibiting maximum noise reduction through enhanced flow attachment and vortex shedding frequency modulation. This research provides theoretical foundations and technical references for pantograph aerodynamic noise control systems of high-speed trains.