Growing global data traffic requires high-performance modulators with a compact size, a large bandwidth, a low optical loss, and a small power consumption. A careful trade-off among these parameters usually has to be made when designing such a device. Here, we propose and demonstrate an electro-optic ring modulator on the thin-film lithium niobate platform without compromising between any performances. The device exhibits a low on-chip loss of about 0.15 dB with a high intrinsic quality-factor (Q-factor) of . Since a pure coupling modulation is employed, the photon lifetime is no longer a limiting factor for the modulation speed. A large electro-optic bandwidth is obtained without any roll-off up to 67 GHz. The device, with a footprint of , also exhibits a low half-wave voltage of 1.75 V, corresponding to a half-wave voltage length product of considering the 2-mm-long modulation section. Driverless data transmission up to 240 Gb/s is also demonstrated with a peak-to-peak driving voltage of 0.75 V.
We experimentally demonstrate an integrated visible light modulator at 532 nm on the thin-film lithium niobate platform. The waveguides on such platform feature a propagation loss of 2.2 dB/mm while a grating for fiber interface has a coupling loss of 5 dB. Our fabricated modulator demonstrates a low voltage-length product of 1.1 V·cm and a large electro-optic bandwidth with a roll-off of -1.59 dB at 25 GHz for a length of 3.3 mm. This device offers a compact and large bandwidth solution to the challenge of integrated visible wavelength modulation in lithium niobate and paves the way for future small-form-factor integrated systems at visible wavelengths.
As ferroelectric materials, lithium tantalate and lithium niobate share similar material characteristics, such as a high Pockels effect and nonlinear optical coefficients. When compared to lithium niobate, lithium tantalate offers a higher optical damage threshold, a broader transparent window, and lower birefringence, making it a promising candidate for high-performance electro-optical photonic integrated devices. In this study, we design and successfully fabricate micro-ring resonators on an acoustic-grade lithium-tantalate-on-insulator wafer, demonstrating their tunability and dynamic modulation capabilities. Experimental results indicate that the achieved thin-film lithium tantalate based micro-ring resonator exhibits an intrinsic Q-factor of 8.4 × 105, corresponding to a waveguide propagation loss of 0.47 dB/cm and a tuning efficiency of 1.94 pm/V. More importantly, as compared to those based on thin-film lithium niobate, a much weaker photorefractive effect and drift phenomenon around the 1550 nm wavelength under a direct-current drive are observed in the present fabricated thin-film lithium tantalate micro-rings with a silicon oxide over-cladding and a tuning electrode on top.
A polarization splitter-rotator device can facilitate on-chip polarization-division multiplexing to enhance the transmission data rate. Here, we propose and experimentally demonstrate a polarization splitter-rotator based on adiabatic mode evolution on the thin-film lithium niobate platform. The measured results for a fabricated device show low insertion losses of <−0.5 dB and large extinction ratios of >20 dB over the 110-nm band. Large fabrication tolerance is also demonstrated with extinction ratios of >15 dB in the wavelength range of 1465–1630 nm for a waveguide width variation of 80 nm.
A two-dimensional grating coupler for coupling light between a standard single-mode fiber and ridge waveguides on an X-cut lithium niobate thin-film is designed and demonstrated. Using circular holes for grating cells, simulated coupling losses reach −3.88 dB at 1550 nm and −5.78 dB at 1563 nm with 1-dB bandwidths of 49 nm and 45 nm for P-polarized and S-polarized light inputs, respectively. Experimentally, peak coupling losses of −5.13 dB at 1561 nm and −7.6 dB at 1568 nm are obtained for P-polarized and S-polarized light inputs, respectively, and corresponding 1 dB bandwidths are about 30 nm. An approach to improve the coupling performance of the grating coupler is also proposed using two crossing ellipses as grating cells as well as a bottom metal reflector. The coupling loss and the polarization dependent loss are decreased to around −3.4 dB and 0.44 dB, respectively.
In this work, we propose and experimentally demonstrate a broadband polarization splitter-rotator (PSR) on the lithium niobate on insulator (LNOI). With multiple sequentially connected adiabatic tapers for waveguide mode conversion and directional coupling, the PSR shows a 160-nm bandwidth covering the C and L bands, an insertion loss of less than 2 dB, and an extinction ratio of more than 11 dB. Benefiting from the conversion-enhanced adiabatic tapers, the broadband device has a short length of 405 µm. Further optimization is performed to reduce the device length to 271 µm and comparable performances are achieved, demonstrating the feasibility of higher device compactness. The proposed design and principle can contribute to high-performance polarization management for integrated lithium niobate photonics.