This research examines the influence of adding a commercial ionic liquid to the electrolyte during the electrochemical anodization of tungsten for the fabrication of WO3 nanostructures for photoelectrochemical applications. An aqueous electrolyte composed of 1.5 M methanesulfonic acid and 5% v/v [BMIM][BF4] or [EMIM][BF4] was used. A nanostructure synthesized in an ionic-liquid-free electrolyte was taken as a reference. Morphological and structural studies of the nanostructures were performed via field emission scanning electron microscopy and X-ray diffraction analyses. Electrochemical characterization was carried out using electrochemical impedance spectroscopy and a Mott–Schottky analysis. From the results, it is highlighted that, by adding either of the two ionic liquids to the electrolyte, well-defined WO3 nanoplates with improved morphological, structural, and electrochemical properties are obtained compared to samples synthesized without ionic liquid. In order to evaluate their photoelectrocatalytic performance, the samples were used as photocatalysts to generate hydrogen by splitting water molecules and in the photoelectrochemical degradation of methyl red dye. In both applications, the nanostructures synthesized with the addition of either of the ionic liquids showed a better performance. These findings confirm the suitability of ionic liquids, such as [BMIM][BF4] and [EMIM][BF4], for the synthesis of highly efficient photoelectrocatalysts via electrochemical anodization.
WO3 nanorods were fabricated following electrochemical anodization of tungsten, under controlled hydrodynamic conditions, in electrolytes containing three distinct carboxylic acids: citric, tartaric and L-aspartic acids, to study the influence of these complexing agents on the morphology and arrangement of the oxide layers. The samples were characterized by FESEM, TEM and XRD, and electrochemical analyses (EIS and ECSA) to assess their potential as anode materials for lithium-ion batteries. This characterization showed the nanostructures anodized in the presence of tartaric acid exhibit uniform morphology and lower total charge transfer resistance associated with the nanostructured layer of WO3 and cycling stability, resulting in more efficient electrochemical processes, better conductivity and stability, making these nanostructures promising for anodes in lithium-ion batteries. The cycling of the batteries was also conducted to understand the behavior of the nanostructures as anodes against metallic lithium. The results showed that the nanostructures analyzed in the presence of tartaric acid exhibited the best initial specific capacity, improving the capacity provided by the graphite ones. These samples also showed a good recovery after faster cycling. These findings demonstrate the effectiveness of complexing-agent-assisted anodization as a strategy for tailoring WO3 nanostructures with enhanced electrochemical performance.
The development of sustainable fabrication routes for advanced semiconductor materials is crucial for environmental technology. This work presents a green electrochemical anodization strategy to fabricate tungsten trioxide (WO3) nanostructures, employing aqueous extracts of two Mediterranean plants, Cistus monspeliensis and Cistus albidus, as environmentally benign electrolytes. Nanostructures synthesized with varying extract percentages were comprehensively characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and electrochemical impedance spectroscopy measurements. Their performance was evaluated in photoelectrocatalytic (PEC) tests under simulated sunlight. The WO3 nanostructures anodized in the presence of optimal concentrations of C. albidus (7%) and C. monspeliensis (5%) extracts demonstrated superior properties. These optimal samples were then applied to degrade ciprofloxacin, a persistent antibiotic pollutant. The C. albidus-derived photoelectrocatalyst exhibited markedly higher efficiency, achieving a degradation rate constant of 1.76 h-1, which is four times faster than the 0.43 h-1 constant obtained for the C. monspeliensis-based sample. This study confirms that plant extracts can effectively tune the properties of anodized WO3 and introduces Cistus albidus extract as a particularly effective green agent for fabricating high-performance PEC materials for the removal of emerging water pollutants, using a green fabrication process to create high-performance materials for environmental cleanup.
9 May 2026 in Chemical Engineering Journal Advances