Punnathat Bordeenithikasem

Dr. Punnathat Bordeenithikasem

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2018 in Materials Today
Verified
Journal Article
Open access
MGMichael A. Gibson
Michael A. Gibson
NMNicholas M. Mykulowycz
Nicholas M. Mykulowycz
JSJoseph Shim
Joseph Shim
RFRichard Fontana
Richard Fontana
PSPeter Schmitt
Peter Schmitt
JSJan Schroers
Jan Schroers

13 April 2020 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
DODaniel Oropeza
Daniel Oropeza
DHDouglas C. Hofmann
Douglas C. Hofmann
KWKyle Williams
Kyle Williams
SFSamad Firdosy
Samad Firdosy
PBPunnathat Bordeenithikasem
Punnathat Bordeenithikasem
XLXiaochun Li
Xiaochun Li

22 December 2015 in Advanced Materials
Verified
Journal Article
Closed access
PDF file
GDGustavo Doubek
Gustavo Doubek
RSRyan C. Sekol
Ryan C. Sekol
JLJinyang Li
Jinyang Li
WRWon‐Hee Ryu
Won‐Hee Ryu
FGForrest S. Gittleson
Forrest S. Gittleson
ATAndré D. Taylor
André D. Taylor

2 August 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
PBPunnathat Bordeenithikasem
Punnathat Bordeenithikasem
JLJingbei Liu
Jingbei Liu
SKSebastian A. Kube
Sebastian A. Kube
YLYanglin Li
Yanglin Li
TMTianxing Ma
Tianxing Ma
JSJan Schroers
Jan Schroers
The glass forming ability (GFA) of metallic glasses (MGs) is quantified by the critical cooling rate (RC). Despite its key role in MG research, experimental challenges have limited measured RC to a minute fraction of known glass formers. We present a combinatorial approach to directly measure RC for large compositional ranges. This is realized through the use of compositionally-graded alloy libraries, which were photo-thermally heated by scanning laser spike annealing of an absorbing layer, then melted and cooled at various rates. Coupled with X-ray diffraction mapping, GFA is determined from direct RC measurements. We exemplify this technique for the Au-Cu-Si system, where we identify Au56Cu27Si17 as the alloy with the highest GFA. In general, this method enables measurements of RC over large compositional areas, which is powerful for materials discovery and, when correlating with chemistry and other properties, for a deeper understanding of MG formation.

28 October 2014 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
MKMichael Kanik
Michael Kanik
PBPunnathat Bordeenithikasem
Punnathat Bordeenithikasem
DKDennis Kim
Dennis Kim
NSNate Selden
Nate Selden
ADAmish Desai
Amish Desai
JSJan Schroers
Jan Schroers
By utilizing bulk metallic glasses’ (BMGs) unique combination of amorphous structure, material properties, and fabrication opportunities, ultrasmooth and symmetric 3-D metallic glass resonators that are complimentary metal oxide semiconductor (CMOS) post-processing compatible are fabricated. Surface roughness to size ratio fabrication precision in the order of 100 parts per billion is demonstrated with a 3-mm diameter Pt 57.5 Cu 14.7 Ni 5.3 P 22.5 BMG hemispherical shell with a thickness variation <100 nm and a surface roughness of <1 nm $\mathrm{R}_{\mathrm {a}}$ . The resonator exhibits a resonant frequency of 13.9440 kHz ± 0.1 Hz Hz with 0.035% frequency mismatch between degenerate ${N} = 2$ wineglass modes with a quality factor of 6200. This performance was obtained in the as-molded state without any device tuning or trimming. Another resonator with ${N} = 2$ resonant modes at 9.393 and 9.401 kHz, and quality factors of 7800 and 6500 was mounted into an integrated electrode system. Electrical readout by capacitive sensing in both time and frequency domains showed a resonance shift to 9.461 and 9.483 kHz, respectively. The quality factor was reduced to 5400 and 5300, respectively. This investigation demonstrates that BMG resonators may serve as a basis for robust microelectromechanical systems resonator devices with increased performance and low-cost fabrication techniques that exploits the atomic structure, unique softening behavior, strength, formability, and toughness of metallic glasses. [2014-0187]

1 August 2020 in Materialia
Verified
Journal Article
Closed access
LSLing Shao
Ling Shao
JKJittisa Ketkaew
Jittisa Ketkaew
Pan GongPan Gong
Pan Gong
SZShaofan Zhao
Shaofan Zhao
SSSungwoo Sohn
Sungwoo Sohn
JSJan Schroers
Jan Schroers