As anomaly detection for electrical power steering (EPS) systems has been centralized using model- and knowledge-based approaches, EPS system have become complex and more sophisticated, thereby requiring enhanced reliability and safety. Since most current detection methods rely on prior knowledge, it is difficult to identify new or previously unknown anomalies. In this paper, we propose a deep learning approach that consists of a two-stage process using an autoencoder and long short-term memory (LSTM) to detect anomalies in EPS sensor data. First, we train our model on EPS data by employing an autoencoder to extract features and compress them into a latent representation. The compressed features are fed into the LSTM network to capture any correlated dependencies between features, which are then reconstructed as output. An anomaly score is used to detect anomalies based on the reconstruction loss of the output. The effectiveness of our proposed approach is demonstrated by collecting sample data from an experiment using an EPS test jig. The comparison results indicate that our proposed model performs better in detecting anomalies, with an accuracy of 0.99 and a higher area under the receiver operating characteristic curve than other methods providing a valuable tool for anomaly detection in EPS.
This paper presents a double-sharpened decimation filter based on the application of a Kaiser and Hamming sharpening technique for multistandard wireless systems. The proposed double-sharpened decimation filter uses a pre-droop compensator which improves the passband response of a conventional cascaded integrator-comb filter so that it provides an efficient sharpening performance at half-speed with comparison to conventional sharpened filters. In this paper, the passband droop characteristics with compensation provides –1.6 dB for 1.25 MHz, –1.4 dB for 2.5 MHz, –1.3 dB for 5 MHz, and –1.0 dB for 10 MHz bandwidths, respectively. These results demonstrate that the proposed double-sharpened decimation filter is suitable for multistandard wireless applications.
Electric power steering (EPS) has emerged as a valuable driver-assistance system. In an EPS system, an extensive amount of data collected from various sensors is analyzed to enhance the driving experience. Anomaly detection techniques have shown potential in ensuring the integrity of data patterns and detecting abnormalities to prevent adverse driving incidents, thus improving vehicle safety. However, traditional centralized anomaly detection methods require the collection of data from all EPS sensors, resulting in high communication network overhead. Herein, we propose an approach for anomaly detection using EPS data within a federated learning (FL) framework. Our approach exploits deep learning (DL) on time series data to achieve highly effective anomaly detection. This synergy of FL and DL enables all sensors in an EPS system to collaboratively train the anomaly detection model simultaneously. Our results demonstrate the feasibility of combining FL with DL anomaly detection in EPS systems, thus overcoming the limitations of the traditional centralized approach. The combined FL and DL model performs remarkably well, achieving an F1-Score of 99.01%, outperforming the 98.31%~98.89% achieved by the centralized approach. It also exhibits high generalizability by incorporating insights from all sensors to comprehensively understand diverse driving scenarios. This results in a significant reduction in error rates, ranging from 20% to 33.25%, compared to centralized methods. Additionally, the proposed model exhibits significant advantages over traditional methods, including reduced training time and communication overhead, while maintaining comparable anomaly detection accuracy performance.
This paper presents a cost-effective hybrid low drop-out regulator (LDO) circuitry for state-of-the-art DDR DRAM cores that not only supports various refresh operations, but also meets the JEDEC specification of the refresh period by improving the load-transient response. In order to guarantee a stable output voltage by achieving the precise off-control operation, a load replication circuit with dummy DRAM cells is exploited. The proposed cost-effective LDO has been implemented and fabricated in a standard 180nm CMOS technology and occupies 0.165mm 2 . By adopting the hybrid LDO, voltage droop improvements of 62mV and 110mV, and tRFC gain of 100ns and 120ns are measured with refresh rates of 4K and 8K, respectively. The measured current consumption overhead by 8 hybrid LDOs is 36μA during the 8K refresh operation. The peak current efficiency is 99.6% at a supply voltage of 1.2V.
Occupancy mapping has been widely utilized to represent the surroundings for autonomous robots to perform tasks such as navigation and manipulation. While occupancy mapping in 2-D environments has been well-studied, there have been few approaches suitable for 3-D dynamic occupancy mapping which is essential for aerial robots. This paper presents a novel 3-D dynamic occupancy mapping algorithm called DS-K3DOM. We first establish a Bayesian method to sequentially update occupancy maps for a stream of measurements based on the random finite set theory. Then, we approximate it with particles in the Dempster-Shafer domain to enable real-time computation. Moreover, the algorithm applies kernel-based inference with Dirichlet basic belief assignment to enable dense mapping from sparse measurements. The efficacy of the proposed algorithm is demonstrated through simulations and real experiments.
This paper presents a cost-effective compact 5-bit successive approximation register (SAR) analog-to-digital converter (ADC) for state-of-the-art computing processor and memory applications. The proposed voltage interpolating comparison eliminates the passive components of the digital-to-analog converter (DAC) that generates the reference voltage, which is applied to the comparator of the SAR ADC, thereby minimizing the die area. The compact SAR ADC, with dimensions of 48μm × 470μm without pads, has been implemented and fabricated in a standard 28nm CMOS technology. The measured SNDR and SFDR up to the Nyquist frequency are 29.3 dB and 40.1 dB, respectively. And the peak DNL and INL are measured as 0.44 LSB and 0.76 LSB, respectively. The prototype of SAR ADC consumes 190 μA with a 1.8 V supply voltage and achieves a Walden FoM of 71.9 fJ/conv. The prototype of SAR ADC demonstrates the potential as an on-chip temperature sensor IP core due to its compact size and low power consumption.