Objective: To evaluate the effects of rapid maxillary expansion (RME) on the vocal quality, maxillary central incisors, midpalatal suture, and nasal cavity in patients with maxillary crossbite. Materials and Methods: Coronal CT scans of 30 subjects (14 boys, 16 girls; mean age, 12.01 ± 0.75) were taken before RME (T0), and at the end of the expansion phase (T1). Voice samples of all patients were recorded with a high-quality condenser microphone (RODE NT2-A) on a desktop computer at T0 and T1. Statistical analyses were performed using a paired-sample t -test. The degree of association between the changes in the voice parameters and nasal width was assessed with Pearson's correlation. Results: RME treatment produced a significant increase in the transverse dimensions of the midpalatal suture and nasal cavity between T0 and T1 ( P < .05). The maximum F0 and jitter (%) results were shown to decrease statistically significantly from T0 to T1 ( P < .001 and P = .042, respectively). Between T0 and T1, shimmer (%) and shimmer (dB) exhibited statistically significant increases ( P = .037 and P = .019, respectively). Conclusions: After RME therapy, voice quality differences were found to be associated with increases in nasal width.
Objectives: This in vitro study evaluated the effect of different colouring solutions and primer systems used in the bonding of brackets on enamel colour change and bond strength. Materials and methods: 120 premolar teeth were divided into four main groups; brackets were bonded with 37% orthophosphoric acid + Transbond XT Primer in Group 1, 3 M Single Bond Universal in Group 2, Transbond Plus SEP in Group 3, and G-Premio Bond in Group 4. Each group was divided into three subgroups, and the teeth were placed in a cup containing coffee and tea mixture, in a cup containing cola and in distilled water. A bond strength test was applied to all teeth. Colour measurements of all teeth were performed at 2 different times: before bonding and after the bond strength test. Results: The average bond strength of the 37% orthophosphoric acid group was higher than that of the other groups. The effect of primer and solution groups on colour change was statistically significant (p = 0.001 and p = 0.023, respectively). Conclusions: In this study, the bond strength was clinically sufficient in all primer groups. The highest colour change was observed when the tea–coffee solution and Transbond Plus SEP primer were used. Clinical relevance: This study has identified enamel discoloration and bond strength from different colouring solutions and primer systems used for bonding braces, which can be used to inform clinicians and patients to achieve better treatment results.
10 December 2024 in American Journal of Orthodontics and Dentofacial Orthopedics
Aim: Materials used in orthodontic treatment can cause corrosion and metal ion release to the mouth. This study was aimed to examine the changes in the friction coefficients and corrosion resistance of the modified Ni-Ti arch wires. Methodology: Our sample consisted of 16 Ni-Ti arch wires (0.016 × 0.022 inches). Coating bathes involving Ni-Ti, Ni-Ti-Mo, and Ni-Ti-Cr were prepared for arch wires coating. New surfaces were analyzed by SEM, and the crystallographic structure was determined by X-rays. The friction coefficient of the coated wires was determined by nanoindentation. Artificial saliva was prepared as a corrosive condition. Impedance measurements were performed with an electrochemical analyzer. The AC impedance spectroscopy measurements were performed after four hours, seven, 15, 30, 45, and 60 days. Results: All groups were more resistant than the control group (-447 mV) [group 1 (-388 mV), group 2 (-328 mV), group 3 (-327 mV), group 4 (-427 mV), group 5 (-395 mV), group 6 (-366 mV), and group 7 (-380 mV)]. Friction coefficients of group 5 (0.252) and group 6 (0.265) were observed to be lower than those of the control group (0.288). Conclusion: In the results of our study, it was shown that the surface properties of Ni-Ti wires could be electrochemically improved. The coated wires (group 5 and group 6) had a remarkable corrosion resistance and reduced friction. The protocols that we used should help provide better-quality surfaces. How to cite this article: Özyılmaz AT, Bilgiç Zortuk F, Yılmaz H. Evaluation of the surface properties of modified ni-ti arch wires. Int Dent Res 2021;11(Suppl.1):167-176. https://doi.org/10.5577/intdentres.2021.vol11.suppl1.25 Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.
1 December 2023 in Turkish Journal of Orthodontics
Objective: The aim of this study was to compare the effects of flash-free and conventional adhesive brackets and different finishing techniques on enamel discoloration. Methods: Forty human premolar teeth were utilized and randomly divided into four groups based on the type of brackets and finishing technique: (1) Gemini((R)) brackets were used for orthodontic bonding. After debanding, adhesive remnants were cleaned using a 12-blade tungsten carbide bur. (2) Gemini((R)) suspenders were used for orthodontic bonding. After debanding the brackets, adhesive remnants were cleaned using12-blade APC(TM) Flash-Free brackets were used for orthodontic bonding. After debanding, adhesive remnants were cleaned a 12-blade tungsten carbide bur and polished with Sof-Lex disks. (4) APC(TM) Flash-Free brackets were used for orthodontic bonding. After debanding, the adhesive remnants were cleaned using a 12-blade tungsten carbide bur. A Vita Easyshade spectrophotometer was used to measure the color change values of the 40 teeth. Results: The color change of the enamel surface in the Flash Free bracket group was significantly less than that in the conventional groups (p=0.003 p < 0.05). The mean.E values obtained from the Sof-Lex groups were lower than those obtained from the groups without Sof-Lex, but these results were not statistically significant (p=0.280 p > 0.05). Conclusion: It is recommended to use Flash-Free brackets and polish with Sof-Lex disk following the clean-up procedures to minimize the possibility of discoloration of the teeth during orthodontic treatment.