In this paper, the ultraviolet protection factor (UPF) of weft knitted fabrics made from 20Ne cotton yarn, Coolmax yarn and their blends in dry, relaxed and stretched states were studied. According to the fibre composition, samples were divided into three groups: Group I (single cotton yarn); Group II (cotton/cotton combination); and Group III (Coolmax/cotton combination) for discussion. In addition, yarn and fabric properties such as yarn tenacity, yarn strength, fibre combination and water vapour transmission that affect the corresponding UPF values are used for formulating a prediction model in order to determine UPF. Generally speaking, when samples are measured under stretched conditions in a dry state, they exhibit a remarkable reduction in ultraviolet protective power, as pores are opened up and UV radiation can easily penetrate through these pores. In addition, greater stretch percentage came along with greater reduction in UPF. This can be explained by the fact that the amount and the size of pores increase when samples are subjected to greater tension.

Background: Turning during locomotion involves considerable changes of the body's center of mass and reduced stability, as well as lower limb kinematics and kinetics. However, many previous studies have been carried out to evaluate the effectiveness and applications of orthotic insoles as well as different types of orthotic materials in various clinical symptoms, which are focused primarily on straight line walking. Hence, the influence of custom‐made insoles with the use of advanced three‐dimensional spacer fabrics on biomechanics parameters in terms of plantar pressure distribution and lower limb electromyography during turning movement was studied.Methods: Twelve subjects performed 180‐degree turning at a speed 3.07‐3.74 km/h for five successful trials under 3 insoles conditions: wearing traditional ethylene vinyl acetate insoles and two different spacer‐fabricated insoles, with the plantar pressure and lower limb muscle activity collected simultaneously. Turning movement was broken down into 3 phases for analysis: Turning initiation, turn around and turn termination.Results: There was a statistically significance difference in plantar pressure between the traditional insoles and the insoles made of a spacer fabric as the top layer (p < 0.05). Compared to the traditional insoles, insoles made of a spacer fabric reduced the peak pressure (>12 %) and pressure–time integral (>13 %) in toes, metatarsal head 1 and metatarsal heads 2–3 at turning initiation; (>15 %) and (>17 %) in medial midfoot and medial heel at turn around. Insoles with spacer fabrics on the top and middle layer reduced both pressure parameters (>18 %) in toes and MTH 1 at turn termination. In terms of muscle activities, insoles with two‐layer spacer fabrics could lower maximum muscle activities of vastus lateralis (>16 %; p < 0.05) at turn around.Conclusions: Insoles with different fabrications could offer various pressure offloading patterns across the plantar and muscle activity changes while turning. Insoles with a spacer fabric on the top tend to reduce plantar pressure loading at different regions during turn initiation and turn around phases, while two‐layer spacer‐fabricated insoles may contribute to reduced vastus lateralis muscle activation during turn around. More importantly, this study provides a new dimension in the potential use of the textile‐fabricated insoles which may widen the range of insole materials selection in the design and development of insoles so as to enhance the effectiveness of orthotic treatment.

This paper investigates the use of atmospheric pressure plasma (APP) treatment for improving the surface hydrophobicity of rayon flock synthetic leather with organosilane precursor (tetramethylsilane (TMS)). Plasma deposition of TMS is regarded as an effective, simple, and low-pollution process. The results show that a highly hydrophobic surface is formulated on the rayon flock synthetic leather. Under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP-treated sample with a contact angle of 135° while the untreated sample had a contact angle of 0° (i.e., the fabric surface was completely drenched immediately). Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), and X-ray Photoelectron Spectroscopy (XPS) confirmed the deposition of organosilane.

In this paper, the ultraviolet protection factor (UPF) of plain knitted fabrics made from 20Ne cotton yarns, Coolmax yarn and their combinations in wet, relaxed and stretched states were studied. According to the fiber composition, fabric samples are divided into three groups including Group I (single cotton yarn), Group II (cotton/cotton combination) and Group III (Coolmax/cotton combination) for discussion. In order to study the effect of wet condition on the UPF of different plain knitted fabrics, five wetting solutions, namely: (i) chlorinated pool water; (ii) sea water, (iii) acidic perspiration; (iv) alkaline perspiration and (v) deionized water (DI water) were prepared and the fabrics were wetted with different percentages of 50%, 75% and 100%. The UPF of the plain knitted fabrics in wet, relaxed and stretched states was measured and the results were discussed. In addition, yarn and fabric properties such as yarn tenacity, yarn strength, fiber combination and water vapor transmission, which affect the corresponding UPF values, were used for generating a prediction model in order to determine UPF. Verification of the prediction model was also conducted.

Nowadays, moulding technology has become a remarkable manufacturing process in the intimate apparel industry. Polyurethane (PU) foam sheets are used to mould three-dimensional (3D) seamless bra cups of various softness and shapes, which eliminate bulky seams and reduce production costs. However, it has been challenging to accurately and effectively control the moulding process and bra cup thickness. In this study, the theoretical mechanism of heat transfer and the thermal conductivity of PU foams are first examined. Experimental studies are carried out to investigate the changes in foam materials at various moulding conditions (viz., temperatures, and lengths of dwell time) in terms of surface morphology and thickness by using electron and optical microscopy. Based on the theoretical and experimental investigations of the thermal conductivity of the foam materials, empirical equations of shrinkage ratio and thermal conduction of foam materials were established. A regression model to predict flexible PU foam shrinkage during the bra cup moulding process was formulated by using the Levenberg-Marquardt method of nonlinear least squares algorithm and verified for accuracy. This study therefore provides an effective approach that optimizes control of the bra cup moulding process and assures the ultimate quality and thickness of moulded foam cups.

This research investigates the effects of corona plasma treatment on the mechanical properties of jute/epoxy-reinforced composites, particularly within biomedical application contexts. Plant Fibre Composites (PFCs) are attractive for medical devices and scaffolds due to their environmental friendliness, renewability, cost-effectiveness, low density, and high specific strength. However, their applications are often constrained by inferior mechanical performance arising from poor bonding between the plant fibre used as the reinforcement and the synthetic resin or polymer serving as the matrix. This study addresses the challenge of improving the weak interfacial bonding between plant fibre and synthetic resin in a 2/2 twill-weave-woven jute/epoxy composite material. The surface of the jute fibre is modified for better adhesion with the epoxy resin through plasma treatment, which exposes the jute fibre to controlled plasma energy and utilises dry air (plasma only), argon (Ar) (argon gas with plasma), and nitrogen (N₂) (nitrogen gas with plasma) at two different distances (25 mm and 35 mm) between the plasma nozzle and the fibre surface. In this context, “equilibrium” refers to the optimal combination of plasma power, treatment distance, and gas environment that collectively determines the degree of fibre surface modification. The results indicate that all plasma treatments improve the interlaminar shear strength in comparison to untreated samples, with treatments at 35 mm using N₂ gas showing a 35.4% increase in shear strength. Conversely, plasma treatment using dry air at 25 mm yields an 18.3% increase in tensile strength and a 35.7% increase in Young’s modulus. These findings highlight the importance of achieving an appropriate equilibrium among plasma intensity, treatment distance, and fibre–plasma interaction conditions to maximise the effectiveness of plasma treatment for jute/epoxy composites. This research advances sustainable innovation in biomedical materials, underscoring the potential for improved mechanical properties in environmentally friendly fibre-reinforced composites.