With the popularity of electric vehicles, lithium-ion batteries as a power source are an important part of electric vehicles, and online identification of equivalent circuit model parameters of a lithium-ion battery has gradually become a focus of research. A second-order RC equivalent circuit model of a lithium-ion battery cell is modeled and analyzed in this paper. An adaptive expression of the variable forgetting factor is constructed. An adaptive forgetting factor recursive least square (AFFRLS) method for online identification of equivalent circuit model parameters is proposed. The equivalent circuit model parameters are identified online on the basis of the dynamic stress testing (DST) experiment. The online voltage prediction of the lithium-ion battery is carried out by using the identified circuit parameters. Taking the measurable actual terminal voltage of a single battery cell as a reference, by comparing the predicted battery terminal voltage with the actual measured terminal voltage, it is shown that the proposed AFFRLS algorithm is superior to the existing forgetting factor recursive least square (FFRLS) and variable forgetting factor recursive least square (VFFRLS) algorithms in accuracy and rapidity, which proves the feasibility and correctness of the proposed parameter identification algorithm.
Accurate parameter identification of a lithium‐ion battery is a critical basis in the battery management systems. Based on the analysis of the second‐order RC equivalent circuit model, the parameter identification process using the recursive least squares (RLS) algorithm is discussed firstly. The reason for the RLS algorithm affecting the accuracy and rapidity of model parameter identification is pointed out. And an improved RLS algorithm is proposed, an inner loop with the estimated parameter vector updated multiple times is inserted into the conventional RLS algorithm, so that the identification results are improved. The test platform of a single lithium‐ion battery is built. The experimental results show that the improved RLS algorithm has better tracking ability, smaller prediction error and has a moderate computational burden compared with the conventional RLS algorithm and a variable forgetting factor RLS algorithm.
9 April 2019 in IEEE Transactions on Industrial Electronics
An improved division-summation (D-∑) digital control strategy without high-speed communication is proposed in this paper. Unlike traditional zero-sequence circulating current (ZSCC) control method, the inter-phase circulating current suppression method is discussed and implemented on the basis of the single-phase equivalent circuit in this strategy. The generation mechanism of the inter-phase circulating current is emphatically analyzed. Output voltage compensation and virtual impedance compensation are studied and integrated with the D-∑ digital control method to suppress the circulating current. Experimental platform with three paralleled three-level T-type grid-connected inverters has been set up. The experiments are carried out under the conditions of the impedance match or mismatch among the inverters, the unbalanced grid voltages and the dynamic process such as start-up and step current change. The experimental results verify that the improved D-∑ digital control strategy may effectively restrain the circulating current under various conditions.
3 June 2021 in IEEE Transactions on Industrial Electronics
Aiming at the problem of large harmonic distortion of grid-connected current in high-power grid-connected power generation system under weak sunlight, multiple hybrid power parallel inverters (MHPPIs) composed of some identical high-power inverters and one low-power inverter in parallel are proposed. According to the irradiance change of sunlight, the low-power inverter operates alone or cooperates with the switching process between the high-power inverters to ensure the low grid-connected current harmonics. Where, any inverters operate in four common working processes, such as soft start-up, steady-state operation, abrupt change of current, and soft stop. Due to the short running time of the dynamic process, most of the existing researches focus on the circulating current suppression under the steady-state condition. However, in engineering practice, the dynamic circulating current in the switching process between inverters is more likely to cause the over-current protection and other safe and stable operation problems of parallel inverters. Therefore, a dynamic circulating current suppression method with dynamic impedance matching for parallel inverters is proposed in this article. The working process of the MHPPIs is equivalent to that of two inverters. The dynamic working process is analyzed in detail, and the dynamic impedance mismatch is the main cause of the dynamic circulating current, so the dynamic virtual inductance matching is introduced to suppress it. Meanwhile, an online inductance identification method based on the model reference adaptive system is presented to compensate for the influence of inaccurate inductance parameter on the circulating current suppression and current control. An experimental prototype of equivalent MHPPIs is built and experimental results prove the validity of the proposed control method.
With the wide application of a modular multilevel converter in various power conversion fields, submodule open-circuit fault diagnostics have attracted increasing attention, as some of the existing diagnosis methods have a single function and limited localization speed. Therefore, a simplified and innovative multifunctional hybrid machine learning-based fault diagnosis strategy for the submodules is proposed. Starting from the output characteristics of the faulty submodule, the eigenvalues of the bridge arm current and submodule capacitor voltage during faults are extracted, and the eigenvalues are utilized for fault detection and location via the integration of improved supervised learning and unsupervised learning. Finally, the effectiveness of the proposed method is verified by simulated and experimental results in a three-phase modular multilevel converter topology. In addition, it can diagnose multiple fault types and achieve a high fault identification probability.
A large number of single-phase loads in an islanded microgrid have a bad influence on the alternating current (AC) bus voltage symmetry, which will further impact the power supply for the other loads. In this paper, the combined three-phase inverter is adopted as the distributed generation (DG) interface circuit for its independent control of each bridge. However, the combined three-phase inverter will generate an asymmetrical voltage with the traditional droop control. Moreover, the system impedance also effects the voltage symmetry. Therefore, the improved droop control method based on the self-adjusting P-f and Q-U droop curves and the system impedance voltage drop compensation are proposed. The system control scheme is also designed in detail. A simulation and an experiment under the conditions of the balanced, unbalanced loads are carried out, and the results verify the feasibility and effectiveness of the control strategy.