Root canal disinfection includes mechanical, chemical and biological struggle against microorganisms (MOs). Photodynamic therapy (PDT) and nanoparticle (NP) agents may be proposed as an alternative for use against intracanal infections due to their ability to disrupt biofilm and prevent bacterial adhesion to dentin. The use of NP agents in combination with light/photosensitizer (PS) agents increases the efficiency of PDT in root canal disinfection. The aim of the study was to evaluate the effect of light application - PDT - on the antibacterial activity of the combination of a PS agent (toluidine blue O -TBO) and an NP agent (silver nanoparticles - AgNPs) for the disinfection of the root canals inoculated with Enterococcus faecalis (E. faecalis). In this study, concentrations of 20 ppm of TBO and 10 ppm of AgNPs, which showed the highest antibacterial activity against E. faecalis in the TBO/AgNPs combination, were used according to the preliminary studies. After instrumentation, 120 human, single-rooted, straight-canal mandibular premolars of a standard length of 13 mm were contaminated with bacteria, and experimental procedures were conducted against 21-day-old mature biofilm. The teeth were randomly divided into 5 main experimental groups: TBO/light; AgNPs; TBO/AgNPs; AgNPs/light; and TBO/AgNPs/light. Then, these main groups were divided into 2 subgroups each, according to the 2 application time periods (30 s and 60 s) (n = 10). The remaining 20 teeth constituted positive and negative control groups. The data was analyzed with the Kolmogorov-Smirnov test, one-way analysis of variance (ANOVA), Tukey's honestly significant difference (HSD) test, and the Bonferroni correction. The NaOCl group provided a bacterial reduction that was higher than in all other groups in a statistically significant manner. Light application on the TBO/AgNPs combination was the group that provided the highest bacterial reduction after NaOCl. The photoactivation of the TBO/AgNPs combination led to an increase in the effect of PDT, and it has the potential to be used as an adjunct for disinfection of the root canal system.
The aim of this innovative study was to investigate the feasibility of a modified butt joint preparation with two grooves instead of a ferrule when root dentin tissue is limited in mandibular molars. It was also investigated to what extent the effect of these treatment options on marginal and internal fit and fracture strength (FS) varied according to the type of material and whether or not a fiber ribbon was used at the base. Marginal and internal fit were evaluated using the triple-scan protocol. Statistical analysis was conducted via a three-way analysis of variance (ANOVA). The absolute marginal discrepancy (AMD), marginal discrepancy, and overall fit values for the ceramic group were 127 μm, 108 μm, and 120 μm, respectively, while corresponding values for the hybrid ceramic group were 139 μm, 116 μm, and 130 μm (p < 0.05). The mean FS recorded for ceramic restorations was 662 N, whereas hybrid ceramic restorations demonstrated a significantly higher FS of 903 N (p < 0.001). When material type was assessed independently of preparation design and base configuration, both ceramic and hybrid ceramic exceeded the predefined clinical acceptability threshold for AMD; however, they remained within acceptable limits for the remaining parameters. Among the evaluated configurations, hybrid ceramic restorations incorporating ferrules and fiber-reinforced bases exhibited the highest FS values, whereas ceramic restorations with modified biological widths and lacking fiber reinforcement yielded the lowest FS values.
A three-dimensional finite element analysis (FEA) was performed to evaluate stress accumulation and distribution in endodontically treated immature and mature mandibular molars restored with endocrowns. Three tooth models representing different stages of root development (Cvek 2, Cvek 3, and mature) were generated from cone-beam computed tomography data. Endocrowns were fabricated using lithium disilicate (LDS) and resin nanoceramic (RNC). In immature teeth, two apexification strategies were simulated: a 3 mm mineral trioxide aggregate (MTA) apical plug followed by gutta-percha obturation, and complete canal obturation with MTA. All models were subjected to axial (600 N) and oblique (200 N) loading. A total of 20 finite element models were analysed. Endocrown material and loading direction were the main factors affecting von Mises stress distribution, whereas root development stage and apexification technique showed limited influence. LDS resulted in reduced stress transmission to the residual dentin, despite higher stress accumulation within the restoration itself. In the LDS groups, von Mises stress values in the root dentin ranged from 35.24 to 35.96 MPa under oblique and from 42.93 to 44.45 MPa under axial loading, while the RNC group exhibited higher values (39.36–40.40 MPa and 51.59–53.66 MPa, respectively). These findings indicate that endocrown restoration after apexification is a reliable treatment option for immature mandibular molars with extensive structural loss, with LDS demonstrating more favorable biomechanical behavior.