Cannulated screws with an anterior wire are currently used for managing transverse patellar fracture. However, the addition of anterior wiring with various types of screws via open surgery to increase the mechanical stability is yet to be determined. Hence, this study aimed to compare the mechanical behaviors of a fractured patella fixed with various screws types and at various screw locations with and without the anterior wire. The present study hypothesized that using the anterior wire reduces the fracture gap formation. A finite element (FE) model containing a fractured patella fixed with various types of cannulated screws and anterior wiring was created in this study. Three types of screws, namely partial thread, full thread, and headless compression screws, and two screw depths, namely 5 and 10 mm away from the anterior surface of the patella, were included. The effect of the anterior wire was clarified by comparing the results of surgical fixation with and without the wire. Two magnitudes and two loading directions were used to simulate and examine the mechanical responses of the fractured patella with various fixation conditions during knee flexion/extension. Compared with partial thread and headless compression screws, the full thread screw increased the stability of the fractured patella by reducing fragment displacement, fracture gap formation, and contact pressure while increasing the contact area at the fracture site. Under 400-N in the direction 45°, the full thread screw with 5-mm placement reduced the gap formation by 86.7% (from 2.71 to 0.36 mm) and 55.6% (from 0. 81 to 0. 36 mm) compared with the partial thread screw with 10-mm placement, respectively without and with the anterior wire. The anterior wire along with the full thread screw is preferentially recommended for maintaining the surgical fixation of the fractured patella. Without the use of anterior wiring, the full thread screw with 5-mm placement may be considered as a less invasive alternative; however, simple screw fixation at a deeper placement (10 mm) is least recommended for the fixation of transverse patellar fracture.

Back pain is a common complication of wheelchair-bound elderly people. Seating system is a key factor that influences spinal curvature, back muscle activation, interface pressure, and comfortability. A seating system can maintain lumbar lordosis, lower back muscle activity, and decrease ischial tuberosities pressure, which reduces spinal load and directly influences sitting comfort. Our previous study has confirmed that backward thoracic support showed a relatively higher lumbar lordosis and lower back muscle activity. This study intends to evaluate the influence of backward thoracic support on interface pressure and subjective discomfort. In this study, 18 elderly men were recruited to participate in a random comparison involving 4 sitting postures. These postures comprised relaxed slouching, flat back support, prominent lumbar support, and backward thoracic support sitting. All parameters, including interface pressure (total contact area, average pressure, and peak pressure on backrest and seat) and subjective discomfort (upper-back, mid-back, lower-back, buttocks, and thighs) were measured and compared. The results showed that compared with other sitting postures, backward thoracic support sitting significantly reduced average pressure and peak pressure on seat and increased average pressure and peak pressure on backrest. Concurrently, subjective discomfort in the upper-back, mid-back, lower-back, and buttocks were reduced. The results confirmed that backward thoracic support can maintain favorable wheelchair sitting posture, thereby preventing or reducing the risks of back pain. However, this study was no evaluations on shear forces on butts and neck postures. Future studies investigating shear forces on butts and neck postures are required.

BackgroundTwo parallel cannulated screws along with an anterior wire to construct a tension band is a popular approach in transverse patellar fractures. However, the optimal screw proximity, either deep or superficial screw placements, remains controversial. Hence, a new concept of the addition of a third screw to form a triangular configuration along with the original two parallel screws was proposed in this study. Therefore, the biomechanical effect of the additional third screw on the stability of the fractured patella was investigated with finite element (FE) simulation.MethodsAn FE knee model including the distal femur, proximal tibia, and fractured patella (type AT/OTA 34-C) was developed in this study. Four different screw configurations, including two parallel cannulated screws with superficial (5-mm proximity) and deep (10-mm proximity) placements and two parallel superficial screws plus a third deep screw, and two parallel deep screws plus a third superficial screw, with or without the anterior wire, were considered for the simulation.ResultsResults indicated that the addition of a third screw increased stability by reducing the dorsal gap opening when two parallel screws were deeply placed, particularly on the fractured patella without an anterior wire. However, the third screw was of little value when two parallel screws were superficially placed. In the existence of two deep parallel screws and the anterior wire, the third screw reduced the gap opening by 23.5% (from 1.15mm to 0.88mm) and 53.6% (from 1.21mm to 0.61mm) in knee flexion 45 degrees and full extension, respectively. Furthermore, in the absence of the anterior wire, the third screw reduced the gap opening by 73.5% (from 2mm to 0.53mm) and 72.2% (from 1.33mm to 0.37mm) in knee flexion 45 degrees and full extension, respectively.ConclusionBased on the results, a third cannulated screw superficially placed (5-mm proximity) is recommended to increase stability and maintain contact of the fractured patella, fixed with two parallel cannulated screws deeply placed (10-mm proximity), particularly when an anterior wire was not used. Furthermore, the third screw deeply placed is not recommended in a fractured patella with two parallel superficial screws.