Longhu Cao

Mr. Longhu Cao


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 July 2026 in Metals
Verified
Journal Article
Open access
PDF file
JWJunhao Wang
Junhao Wang
LCLonghu Cao
Longhu Cao
Efficient melting of direct reduced iron (DRI) is essential for improving the stability and productivity of low-carbon steelmaking processes. In this study, the effect of FeO content on DRI melting behavior and coupled interfacial reactions in slag–refractory systems was investigated. Synthetic slags containing 10, 20, and 28 wt.% FeO were prepared, and hot-state melting experiments, viscosity measurements, FactSage calculations, and SEM/EDS analyses were conducted to clarify the relationship among slag properties, DRI melting, and interfacial evolution. The results showed that increasing FeO content significantly accelerated DRI melting and reduced the overall melting time. This improvement was mainly attributed to the enhanced fluidity and heat-transfer capability of the slag. Temperature-centered Arrhenius fitting showed that the apparent viscous-flow activation energies varied only within a limited range when fitting uncertainties were considered, indicating that the decrease in viscosity with increasing FeO content should not be attributed solely to a reduction in activation energy. Instead, the change in slag fluidity is associated with the combined effects of FeO on melt structure, pre-exponential fitting parameters, and temperature-dependent flow behavior. Meanwhile, the calculated thermal conductivity increased with FeO content, further promoting heat transfer from the molten slag to the DRI surface. Microstructural observations revealed that, under low-FeO conditions, a relatively continuous aluminosilicate-rich reaction layer formed at the DRI–slag interface, which hindered slag penetration and delayed melting. In contrast, high-FeO slag exhibited stronger wettability and penetration ability, allowing slag to infiltrate deeply into the porous DRI structure and form an extensive slag–iron mixed reaction zone. At the slag–MgO refractory interface, FeO promoted Fe2+/Mg2+ interdiffusion and the formation of a dense magnesiowüstite, (Mg,Fe)O, reaction layer. However, excessive FeO also intensified slag penetration and refractory corrosion. These results demonstrate that FeO plays a dual role in DRI melting systems by enhancing DRI melting efficiency while simultaneously aggravating refractory degradation, highlighting the need to balance melting performance and refractory stability in FeO-containing slag design.

25 October 2026 in Metals
Verified
Journal Article
Open access
PDF file
HYHan Yin
Han Yin
JYJiayi Yang
Jiayi Yang
LMLingbo Mao
Lingbo Mao
LCLonghu Cao
Longhu Cao
ZWZhongbing Wang
Zhongbing Wang
Charging direct reduced iron (DRI) into a blast furnace alters the softening–melting–dripping behavior of mixed burdens; however, the influencing laws and mechanisms remain unclear. In this study, DRI, pellets, and sinter were used as raw materials to systematically investigate the effect of DRI proportion (0–40%) on the softening–melting–dripping behavior of mixed burdens, and the underlying mechanism was revealed by combining XRD, SEM-EDS, and FactSage thermodynamic simulation. The results show that with increasing DRI proportion, the softening–melting behavior of the mixed burden exhibits a regular variation: the softening start temperature decreases, the softening interval widens, and the melting–dripping interval narrows due to an increase in melting start temperature and a decrease in dripping temperature, indicating an overall improvement in softening–melting–dripping performance. Meanwhile, the maximum pressure difference and total characteristic value decrease by 73.3% and 85.2%, respectively, indicating markedly improved permeability of the burden layer. Moreover, the addition of DRI promotes deep reduction of the mixed burden, leading to a decrease in FeO content. FactSage calculations show that the onset temperature of liquid slag formation decreases, and the equilibrium liquid slag fraction at the maximum pressure-difference temperature decreases. The decrease in basicity combined with FeO fluxing leads to a lower softening start temperature, while reduced primary slag formation and the supporting effect of the DRI metallic skeleton jointly improve bed permeability.