Aromatic alcohols with substituent groups in different positions have been partially oxidised to the corresponding aldehydes in a photocatalytic system in order to investigate the influence of the substituents on reactivity and selectivity to aldehyde. To this aim benzyl alcohol, 2-methoxybenzyl alcohol, 3-methoxybenzyl alcohol, 4-methoxybenzyl alcohol, 2,4-dimethoxybenzyl alcohol, 4-hydroxybenzyl alcohol and 4-hydroxy-3-methoxybenzyl alcohol have been photocatalytically oxidised to their corresponding aldehydes in aqueous TiO2 suspensions under near-UV irradiation. Home-made and commercial rutile TiO2 samples were used as photocatalysts. The catalysts were characterized by XRD, BET, SEM, TEM and TGA measurements. For all the used substrates the main oxidation products were the corresponding aldehydes and CO2. The aromatic alcohols showed selectivity values decreasing with the substituent position on the aromatic ring according the following order: para > ortho > meta. In the presence of two substituent groups, the overall oxidation rate increased while the selectivity decreased. The home-made catalyst generally showed selectivity higher but activity lower than those of the commercial one. The results showed that the reaction rate and selectivity were dependent not only on the catalyst properties such as crystallinity and hydrophilicity but also on the kind and position of the substituent groups of the aromatic alcohols.
The photocatalytic partial oxidation of 4-methoxybenzyl alcohol to the corresponding aldehyde (p-anisaldehyde) was performed under simulated solar irradiation by using home prepared N-doped TiO2 catalysts. The photocatalysts were prepared by a sol–gel method, using TiCl4 as TiO2 precursor and NH4Cl, urea or NH4OH as N-doping sources. A commercial TiO2 (Degussa P25) was also used for comparison aims. The prepared catalysts were characterized by BET specific surface area, XRD, ESEM and UV-vis spectroscopy. The reactivity results show that (i) the doped catalysts are predominantly amorphous, and they show selectivity values far higher than those of the corresponding undoped ones and of well crystallized catalysts – even if the last ones show a higher activity – and (ii) exploitation of solar light significantly increases the reaction selectivity. In addition, different light sources were also used in order to investigate the effect of radiation wavelength ranges on the reactivity and selectivity to aldehyde.
Nanotube structured TiO2 on Ti surface were prepared in ethylene glycol (Ti/TiO2NTEG) medium by anodic oxidation method with different times and then the plates were calcinated at different temperatures. Non-nanotube structured Ti/TiO2, prepared by thermal oxidation method, and nanotube structured TiO2 on Ti plate in hydrogen fluoride solution were also prepared for comparison. Pt loaded Ti/TiO2NTEG photoanodes were also prepared by cyclic voltammetry method with different cycles and the optimum loaded Pt amount was determined. Photoanodes were characterized by using X-ray Diffraction (XRD), Scanning Electron Microscopy-Energy-Dispersive X-ray Analysis (SEM-EDX), and photocurrent methods. XRD analyses proved that almost all TiO2 is in anatase phase. SEM analyses show that nanotubes and Pt nanoparticles on nanotube surface are dispersed quite homogeneously. The longest nanotubes were obtained in the ethylene glycol medium and the nanotube length increased by increasing applied anodic oxidation time. In addition, a linear correlation between nanotube length and XRD peak intensity was found. Moreover, SEM-EDX and XRD analyses evidence that Pt nanoparticles on nanotube surface are metallic and in cubic structure. Photoelectrocatalytic degradation of paraquat was performed using the prepared photoanodes. Moreover, electrocatalytic and photocatalytic degradations of paraquat were also investigated for comparison, however lower activities were observed. These results evidence that the photoanodes show a significant synergy for photoelectrocatalytic activity.
11 November 2019 in Catalysis Science & Technology