Simon Gray

Simon Gray

orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2013 in Acta Materialia
Verified
Journal Article
Closed access
BFB.J. Foss
B.J. Foss
SGSimon Gray
Simon Gray
MHM.C. Hardy
M.C. Hardy
SSS. Stekovic
S. Stekovic
DMD.S. McPhail
D.S. McPhail
BSB.A. Shollock
B.A. Shollock

3 January 2018 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
NMNicolau Iralal Morar
Nicolau Iralal Morar
RRRajkumar Roy
Rajkumar Roy
JMJörn Mehnen
Jörn Mehnen
SMSundar Marithumu
Sundar Marithumu
SGSimon Gray
Simon Gray
JNJohn Rayment Nicholls
John Rayment Nicholls
This paper presents an experimental investigation on the influences of laser trepanning drilling process parameters on the recast layer thickness and surface crack formation in CMSX-4 nickel-based superalloy angled holes. The effects of peak power, pulse frequency and the trepanning speed as input parameters were investigated in details by varying the laser drilling conditions using Taguchi orthogonal array-based design of experiment approach. Analysis of variance identifies the significant parameters affecting the output responses. It is found that the output responses are affected mainly by the peak power and trepanning speed. The experimental results reveal that the recast layer thickness increases with the increase of peak power and trepanning speed whereas the crack number density decreases with the increase of peak power only. Pulse frequency has no significant effect on both output responses within the range of values investigated. The knowledge gained in this parametric study could be used to improve the metallurgical characteristics of laser-drilled nickel-based acute angled holes.

8 April 2016 in Materials at High Temperatures
Verified
Journal Article
Open access
GGG. J. Gibson
G. J. Gibson
KPK. M. Perkins
K. M. Perkins
SGSimon Gray
Simon Gray
ALA. J. Leggett
A. J. Leggett
High-temperature corrosion fatigue, a combination of corrosion with a fatigue cycle, is an emerging generic issue affecting power generation and aero gas turbine engines and has the potential to limit component life. Historically, surface treatments, such as shot peening have been used to improve component life and have been optimised for fatigue response. Research into optimisation of shot peening techniques for hot corrosion and high-temperature corrosion fatigue has shown 6–8A 230H 200% coverage to provide overall optimum performance for nickel-based superalloy 720Li based on the limited data within this study. Utilisation of electron backscatter diffraction techniques, in combination with detailed assessment of corrosion products have been undertaken as part of this work. The resultant cold-work visualisation technique provides a novel method of determining the variation in material properties due to the shot peening process and the interaction with hot corrosion. Through this work it has been shown that all three shot peening outputs must be considered to minimise the effect of corrosion fatigue, the cold work, residual stress and surface roughness. Further opportunity for optimisation has also been identified based on this work.

1 September 2017 in International Journal of Fatigue
Verified
Journal Article
Open access
NMN. Morar
N. Morar
RRR. Roy
R. Roy
JMJ. Mehnen
J. Mehnen
JNJohn Rayment Nicholls
John Rayment Nicholls
SGSimon Gray
Simon Gray
The effect of laser trepanning speed and, as a result, recast layer thickness on the high temperature corrosion fatigue behaviour of CMSX-4 superalloy acute angled holes was investigated. The experimental test results show that an increasing laser drilling speed caused a reduction in corrosion fatigue life by 30-50% at 850°C, under low cycle fatigue regime. This reduction was found to correlate directly with the recast layer thickness and surface anomalies within the recast layer produced during the laser drilling process. Corrosion had a smaller effect on the overall life of the laser drilled specimens under the conditions tested. The results presented show that laser trepanning speedis influencial in limiting the life performance of laser drilled components in service

1 November 2018 in International Journal of Fatigue
Verified
Journal Article
Open access
LBL. Brooking
L. Brooking
SGSimon Gray
Simon Gray
JSJoy Sumner
Joy Sumner
JNJohn Rayment Nicholls
John Rayment Nicholls
GMG. Marchant
G. Marchant
NSN.J. Simms
N.J. Simms

1 December 2018 in International Journal of Fatigue
Verified
Journal Article
Open access
LBL. Brooking
L. Brooking
SGSimon Gray
Simon Gray
JSJoy Sumner
Joy Sumner
JNJ.R. Nicholls
J.R. Nicholls
NSN.J. Simms
N.J. Simms