Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
2 May 2009 in IEEE Journal of Solid-State Circuits
An integrated receiver that includes both the time-to-digital converter (TDC) and the receiver channel and is intended for a pulsed time-of-flight laser rangefinder with a measurement range of approximately 10 m has been designed and fabricated in a standard 0.13 mum CMOS process. The receiver operates by detecting the current pulse of an optical detector and producing a stop timing mark for the TDC by means of a leading edge timing discriminator. The TDC is used to measure the actual time interval between the start and stop pulses and the slew-rate of the stop pulse, to compensate for a walk error produced in the discriminator. The single-shot precision of the whole receiver is 250 ps for a minimum detectable signal, and its accuracy and power consumption are plusmn 37 ps with compensation within a dynamic range of at least 1:10,000 and less than 45 mW, respectively. The size of the die is 1300 mum times1300 mum including pads.
This paper discusses the construction principles and performance of a pulsed time-of-flight (TOF) laser radar based on high-speed (FWHM ~100 ps) and high-energy (~1 nJ) optical transmitter pulses produced with a specific laser diode working in an “enhanced gain-switching” regime and based on single-photon detection in the receiver. It is shown by analysis and experiments that single-shot precision at the level of 2W3 cm is achievable. The effective measurement rate can exceed 10 kHz to a noncooperative target (20% reflectivity) at a distance of > 50 m, with an effective receiver aperture size of 2.5 cm 2 . The effect of background illumination is analyzed. It is shown that the gating of the SPAD detector is an effective means to avoid the blocking of the receiver in a high-level background illumination case. A brief comparison with pulsed TOF laser radars employing linear detection techniques is also made.
A 16×256 element single-photon avalanche diode (SPAD) array with a 256-channel, 3-bit on-chip time-to-digital converter (TDC) has been developed for fluorescence-suppressed Raman spectroscopy. The circuit is fabricated in 0.35 μm highvoltage CMOS technology and it allows a measurement rate of 400 kframe/s. In order to be able to separate the Raman and fluorescence photons even in the presence of the unavoidable timing skew of the timing signals of the TDC, the time-of-arrival of every detected photon is recorded with high time resolution at each spectral point with respect to the emitted short and intensive laser pulse (~150ps). The dynamic range of the TDC is set so that no Raman photon is lost due to the timing skew, and thus the complete time history of the detected photons is available at each spectral point. The resolution of the TDC was designed to be adjustable from 50 ps to 100 ps. The error caused by the timing skew and the residual variation in the resolution of the TDC along the spectral points is mitigated utilizing a calibration measurement from reference sample with known smooth fluorescence spectrum. As a proof of concept, the Raman spectrum of sesame seed oil, having a high fluorescence-to-Raman ratio and a short fluorescence lifetime of 1.9 ns, was successfully recorded.
A time-gated single photon avalanche diode (SPAD) has been designed and fabricated in a standard high voltage 0.35 μm CMOS technology for Raman spectroscopy. The sub-ns time gating window is used to suppress the fluorescence background typical of Raman studies, and also to minimize the dark count rate in order to maximize the signal-to-noise ratio of the Raman signal. The proposed time-gating technique is applied for measuring the Raman spectra of olive oil with a gate window of 300 ps, and shows significant fluorescence suppression.
An integrated ring oscillator based time-to-digital converter (TDC) for a pulsed time-of-flight laser rangefinder has been designed and tested. The time-to- digital conversion is based on counting the pulses of this eight-stage differential ring oscillator and additionally registering the state of its 16 phases at the arrival moment of the timing signals. The single-shot precision and the nonlinearity of the TDC are better than 78.5 ps and ±37 ps, respectively and the current consumption of the time-to-digital converter is < 24 mA from a +3 V power supply. The time-to-digital converter was fabricated on the same chip with a receiver channel in a 0.35 μm CMOS process.