Ice accretion along aircraft leading edges, particularly at stagnation line parting strips, remains difficult to remove using conventional electrothermal anti-icing systems. These systems require continuous high-power heating to maintain the stagnation region above the melting point, often exceeding 10–12 kW/m2. This study introduces an Ice Cavitation Deicer (ICD) that removes ice through rapid, localized cavitation generated within a thin melt layer formed at the ice–surface interface. In the proposed approach, a short pulse of electric current melts a 1–10 µm interfacial layer and causes a cavitation impulse of approximately 1–10 MPa. This impulse ejects the stagnation-line ice in a direction normal to the surface, often against the external airflow, enabling the immediate aerodynamic removal of the remaining ice. Analytical modeling based on the energy conservation principle was used to determine the optimal foil geometry, thermal pulse parameters, thermal stress, and material selection. Experiments with various metallic foils and substrate materials validated the predicted ejection behavior. The impulses were sufficient to fracture and eject ice 1–10 mm thick. The observed ice fragment velocities varied from 1 m/s to 10 m/s. Compared with conventional thermal anti-icing, the ICD concept reduces power consumption by approximately two orders of magnitude while offering rapid and reliable leading-edge deicing. The low power requirements, rapid response, and compatibility with thin-foil heater architectures make ICD a promising technology for both conventional and electrified aircrafts, UAVs, rotorcrafts, and other platforms where power availability is limited. This manuscript presents the first theoretical and experimental research on the ICD method and is a concept-proof work. Further research and development are required before the ICD is ready to be tested in flight.
Ice accretion along aircraft leading edges, particularly at stagnation line parting strips, remains difficult to remove using conventional electrothermal anti-icing systems. These systems require continuous high-power heating to maintain the stagnation region above the melting point, often exceeding 10–12 kW/m². This study introduces an Ice Cavitation Deicer (ICD) that removes ice through rapid, localized cavitation generated within a thin melt layer formed at the ice–surface interface. In the proposed approach, a short pulse of electric current melts a 1–10 µm interfacial layer and causes a cavitation impulse of approximately 1–10 MPa. This impulse ejects the stagnation line ice in a direction normal to the surface, often against the external airflow, enabling the immediate aerodynamic removal of the remaining ice. Analytical modeling based on the energy conservation principle was used to determine the optimal foil geometry, thermal pulse parameters, thermal stress, and material selection. Experiments with various metallic foils and substrate materials validated the predicted ejection behavior. Compared with conventional thermal anti-icing, the ICD concept reduces power consumption by approximately two orders of magnitude while offering rapid and reliable leading-edge deicing.
Ice accumulation on aerodynamic surfaces remains a major safety and efficiency challenge for aircraft. Conventional electrothermal deicing systems are reliable but often require more electrical power than is available on small, medium-sized, and unmanned aircraft, whereas electro-impulsive deicers introduce structural fatigue and mechanical complexity. Recently developed Ice Cavitation Deicing (ICD) demonstrated highly efficient ice removal by explosively vaporizing a thin interfacial water layer. However, the original high-temperature ICD (HTICD) operates at heating rates above 106 K/s and cavitation temperatures near 300 °C, producing foil temperatures exceeding 400 °C and requiring high-voltage film capacitors. This study develops and experimentally validates Low-Temperature and Medium-Temperature Ice Cavitation Deicing (LTICD and MTICD), extending the concept of impulse cavitation deicing into the previously unexplored intermediate heating-rate regime. Analytical modeling based on energy conservation, transient heat diffusion, water thermodynamics, and thermal-stress analysis was combined with finite-element simulations and extensive experimental testing. Stainless steel 17-7PH, titanium Grade 5, titanium Grade 1, Invar, and other foil materials were evaluated over heating rates ranging from approximately 104 to 107 K/s using capacitor banks from 0.1 to 35 mF. The experimental results demonstrate that both LTICD and MTICD effectively remove thick and thin ice while operating at cavitation temperatures of approximately 120–200 °C, substantially below those of HTICD. The lower operating temperatures and heating rates reduce thermal stress, operating voltage, and current, enable the use of practical low-voltage electrolytic capacitors, and expand the range of suitable foil and substrate materials. These results demonstrate that the cavitation-deicing mechanism can be implemented at substantially lower temperatures and with a more practical electrical architecture than HTICD, making LTICD and MTICD promising candidates for future aircraft ice-protection systems.
This manuscript presents the theory and experimental validation of low- and medium-temperature deicing technology that advances the recently developed Ice Cavitation Deicing (ICD) method. Conventional high-temperature ICD (HTICD) efficiently removes ice by explosively vaporizing a thin interfacial melted layer but operates at heating rates above 106 K/s, high voltage, and maximum temperatures exceeding 400 °C. This study develops Low-Temperature and Medium-Temperature Ice Cavitation Deicing (LTICD and MTICD), extending ICD into the previously unexplored intermediate heating-rate regime. Analytical modeling based on energy conservation, transient heat diffusion, water thermodynamics, and thermal-stress analysis was combined with finite-element simulations and experimental testing. Several foil materials were evaluated over heating rates of approximately 104–107 K/s using capacitor banks of 0.1–35 mF. Experiments demonstrated effective removal of thick and thin ice at cavitation temperatures of approximately 120–200 °C, substantially below those of HTICD. The lower operating temperatures and heating rates reduce thermal stress, voltage, and current, enable practical low-voltage electrolytic capacitors, and expand the range of suitable materials. Thus, LTICD and MTICD provide a lower-temperature, more practical electrical architecture for future aircraft ice-protection systems.