The marine environment is complex and changeable, and the interference of noise and reverberation seriously affects the classification performance of active sonar equipment. In particular, when the targets to be measured have similar characteristics, underwater classification becomes more complex. Therefore, a strong, recognizable algorithm needs to be developed that can handle similar feature targets in a reverberation environment. This paper combines Fisher’s discriminant criterion and a dictionary-learning-based sparse representation classification algorithm, and proposes an active sonar target classification method based on Fisher discriminant dictionary learning (FDDL). Based on the learning dictionaries, the proposed method introduces the Fisher restriction criterion to limit the sparse coefficients, thereby obtaining a more discriminating dictionary; finally, it distinguishes the category according to the reconstruction errors of the reconstructed signal and the signal to be measured. The classification performance is compared with the existing methods, such as SVM (Support Vector Machine), SRC (Sparse Representation Based Classification), D-KSVD (Discriminative K-Singular Value Decomposition), and LC-KSVD (label-consistent K-SVD), and the experimental results show that FDDL has a better classification performance than the existing classification methods.
Compressive sensing can guarantee the recovery accuracy of suitably constrained signals by using sampling rates much lower than the Nyquist limit. This is a leap from signal sampling to information sampling. The measurement matrix is key to implementation but limited in the acquisition systems. This article presents the critical elements of the direct under-sampling—compressive sensing (DUS–CS) method, constructing the under-sampling measurement matrix, combined with a priori information sparse representation and reconstruction, and we show how it can be physically implemented using dedicated hardware. To go beyond the Nyquist constraints, we show how to design and adjust the sampling time of the A/D circuit and how to achieve low-speed random non-uniform direct under-sampling. We applied our method to data measured with different compression ratios (volume ratios of collected data to original data). It is shown that DUS-CS works well when the SNR is 3 dB, 0 dB, −3 dB, and −5 dB and the compression ratio is 50%, 20%, and 10%, and this is validated with both simulation and actual measurements. The method we propose provides an effective way for compressed sensing theory to move toward practical field applications that use underwater echo signals.
1 September 2018 in The Journal of the Acoustical Society of America
Reducing data volume and improving signal-to-noise ratio (SNR) is of great importance for echoes from submerged targets, affected by serious marine environment noise. The echo from a target is made of its response to the incident wave with the superposition of highlights (sub-echoes from main constituents of the target). Each of these highlights can be seen as a block, and the echo therefore has a block-sparse feature. This paper proposes a compressive sensing method to leverage prior information (CSPI), in which knowledge of the incident wave and the block-sparse feature are leveraged into the dictionary structure and signal reconstruction. CSPI is illustrated with simulations and field measurements of backscattering for a 1:20 model of the Benchmark Target Strength Simulation Submarine. For simulated signals with different noise levels, CSPI can reconstruct an almost invisible signal (original SNR = 0 dB), and improve SNR by up to 13 dB (for an original SNR of 4 dB) down to a still significant SNR of 7 dB (for an original SNR of 0 dB). For field measurements, CSPI can obtain the same SNR as the original signal using only 13% of the data, increasing the SNR to 15 dB using 30% data, and increasing with the compression ratio.
Ocean reverberations, a significant interference source in active sonar, arise as a response generated by random scattering at the receiving end, a consequence of randomly distributed clutter or irregular interfaces. Statistical analysis of reverberation data has revealed a predominant adherence to the Rayleigh distribution, signifying its departure from specific distribution forms like the Gaussian distribution. This study introduces the Gaussian mixture model, capable of simulating random variables conforming to a wide array of distributions through the integration of an adequate number of components. Leveraging the unique statistical attributes of reverberation, we initiate the Gaussian mixture model’s parameters via the frequency histogram of the reverberation data. Subsequently, model parameters are estimated using the expectation–maximization (EM) algorithm and the most suitable statistical model is selected based on robust model selection criteria. Through a comprehensive evaluation that encompasses both simulated and observed data, our results underscore the Gaussian mixture model’s effectiveness in accurately characterizing the distribution of reverberation data, yielding a mean squared error of less than 4‰.
The compressive sensing method is an effective way of under-sampling array signal processing, and the measurement matrix is a key technology of compressive sensing processing, which is of decisive significance to improve the performance of under-sampling array signal processing. In this paper, an under-sampling array signal processing method based on an improved Hadamard measurement matrix was proposed. This method improved the construction of the measurement matrix by a compressing zero method capable of reducing the redundant data, enhancing the non-correlation between columns, improving the RIP condition, and improving the performance of the compressive sensing method. The performance was verified by simulation and real data from the lake, and the results showed that the method proposed in this paper has obvious performance advantages compared with the Toeplitz Circular Matrix, the m-sequence-based matrix, and the partial Hadamard matrix under the same conditions.
Compressive sensing is a very attractive technique to detect weak signals in a noisy background, and to overcome limitations from traditional Nyquist sampling. A very important part of this approach is the measurement matrix and how it relates to hardware implementation. However, reconstruction accuracy, resistance to noise and construction time are still open challenges. To address these problems, we propose a measurement matrix based on a cyclic direct product and QR decomposition (the product of an orthogonal matrix Q and an upper triangular matrix R). Using the definition and properties of a direct product, a set of high-dimensional orthogonal column vectors is first established by a finite number of cyclic direct product operations on low-dimension orthogonal “seed” vectors, followed by QR decomposition to yield the orthogonal matrix, whose corresponding rows are selected to form the measurement matrix. We demonstrate this approach with simulations and field measurements of a scaled submarine in a freshwater lake, at frequencies of 40 kHz–80 kHz. The results clearly show the advantage of this method in terms of reconstruction accuracy, signal-to-noise ratio (SNR) enhancement, and construction time, by comparison with Gaussian matrix, Bernoulli matrix, partial Hadamard matrix and Toeplitz matrix. In particular, for weak signals with an SNR less than 0 dB, this method still achieves an SNR increase using less data.