As a super-resolution imaging method, compressive imaging (CI) has become a research hotspot in recent years. However, most researchers focus on the visible light and near-infrared regime. Further, most experimental studies are confined to a single-pixel camera, and there are comparatively few reports of the experimental studies about CI in the field of focal plane array-based (FPA) CI in the medium-wave infrared (MWIR). This paper derives the system model for an FPA CI system, describes the generation process of DMD masks, and modifies the block-based compressive sensing algorithm to be applicable to the FPA CI system. Based on the actual FPA CI system in MWIR, high-resolution MWIR images are obtained from a low-resolution MWIR sensor, realizing 16 times MWIR image super-resolution. However, imaging quality is not as ideal as that in visible light FPA CI system because of the particularities of MWIR. We analyze the particularities of an FPA CI system in MWIR and provide suggestions on how to solve them to improve performance. This work could provide guidance for researchers to build an experimental FPA CI system in MWIR.
As a super-resolution imaging method, high-resolution medium wave infrared (MWIR) images can be obtained from a low-resolution focal plane array-based (FPA) sensor using compressive imaging (CI) technology. As a common problem in MWIR FPA imaging, the non-uniformity reduces image quality, which is turning worse in MWIR FPA CI. This paper investigates the source of the non-uniformity of MWIR FPA CI, both in the captured low-resolution MWIR images and in the reconstructed high-resolution ones. According to the system model and the image super-resolution computation process of FPA CI, we propose a calibration-based non-uniformity correction (NUC) method for MWIR FPA CI. Based on the actual MWIR FPA CI system, the effectiveness and practicability of the proposed NUC method are verified, obtaining better results than the traditional method. According to the theoretical analysis and experimental results, the particularities of the non-uniformity in MWIR FPA CI are discovered and discussed, which have certain great guiding significance and practical value.
With medium wave infrared (MWIR) focal plane array-based (FPA) compressive imaging (CI), high-resolution images can be obtained with a low-resolution MWIR sensor. However, restricted by the size of digital micro-mirror devices (DMD), aperture interference is inevitable. According to the system model of FPA CI, aperture interference aggravates the blocky structural artifacts (BSA) in the reconstructed images, which reduces the image quality. In this paper, we propose a novel DMD mask design strategy, which can effectively suppress BSA and maximize the reconstruction efficiency. Compared with random binary codes, the storage space and computation cost can be significantly reduced. Based on the actual MWIR FPA CI system, we demonstrate the proposed DMD masks can effectively suppress the BSA in the reconstructed images. In addition, a new evaluation index, blocky root mean square error, is proposed to indicate the BSA in FPA CI.
With focal plane array-based (FPA) compressive imaging (CI), high-resolution medium wave infrared (MWIR) images can be reconstructed by a low-resolution FPA sensor. However, in MWIR FPA CI system, the stray light is inevitable, which reduces the image contrast and increases the blocky structural artifacts of the reconstructed images. In this work, we focus on the stray light in MWIR FPA CI system. This paper investigates the sources of stray light in MWIR FPA CI system and modifies the systematic radiation model. According to the systematic computation model, we illustrate that stray light impedes the accurate sampling of compressive measurements in the MWIR FPA CI system, which may increase the blocky structural artifacts in the reconstructed high-resolution images. With the help of digital micro-mirror device modulation, we propose an operational method to substantially correct the effect of the stray light in MWIR FPA CI system, which can improve the image contrast and reduce the blocky structural artifacts of the reconstructed images, while not significantly increasing the cost of image acquisition and computation. Based on the experimental results obtained from the actual MWIR FPA CI system, we have verified the effectiveness and practicability of the proposed stray light correction method.