Yudong Dang

Dr. Yudong Dang


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 July 2018 in Journal of Wuhan University of Technology-Mater. Sci. Ed.
Verified
Journal Article
Closed access
PDF file
YDYudong Dang
Yudong Dang
Xianming ShiXianming Shi
Xianming Shi
JQJueshi Qian
Jueshi Qian
YJYan Jiang
Yan Jiang
XLXincheng Li
Xincheng Li

21 February 2022 in Buildings
Verified
Journal Article
Open access
PDF file
WMWenting Mao
Wenting Mao
CCChunpeng Cao
Chunpeng Cao
XLXincheng Li
Xincheng Li
JQJueshi Qian
Jueshi Qian
YDYudong Dang
Yudong Dang
Magnesium ammonium phosphate cement (MAPC) prepared with ammonium dihydrogen phosphate (NH4H2PO4, ADP) and dead-burned Magnesium oxide (MgO) is a new type of rapid patch repair material for concrete structures. In order to reduce the material costs of MAPC mortar, manufactured limestone sands, being a more widely-available resource with lower cost, was investigated in this study as an alternative to quartz sands for the preparation of MAPC mortar. The limestone fines in manufactured sands were found to be the key factor that influences properties of MAPC mortar by causing bubbling and volume expansion before hardening. As a result, the mechanical strength of MAPC mortar decreased with the increasing content of limestone fines due to increased porosity. According to microstructure analysis, the mechanism of these negative effects can be inferred as the reaction between limestone fines and ADP with the gas generation of CO2 and NH3. This reaction mainly occurred during a short period before setting while most limestone fines remained unreactive in the hardened MAPC mortar. Based on the above detailed experimental findings on the effects of limestone fines in manufactured sand on the properties of MAPC mortar, this paper pointed out that effective defoaming methods for inhibiting bubbling was the key to the utilization of manufactured sands in preparation of high performance MAPC mortar.

18 February 2026 in Coatings
Verified
Journal Article
Open access
PDF file
RWRuihai Wang
Ruihai Wang
XLXiang Liu
Xiang Liu
YDYudong Dang
Yudong Dang
XLXiaolong Li
Xiaolong Li
JCJie Chen
Jie Chen
Waste oyster shell powder (OP) and calcined oyster shell powder (COP) were used as bio-fillers in asphalt mastics. Limestone powder (LP) served as the control. This study employed rheological theory to quantify filler–asphalt interactions. Dynamic shear rheometry (DSR), Black diagrams, and master curves were analyzed to determine critical volume fraction (φcrit), interaction parameter (C), and complex viscosity increment (∆η*). Results indicate that OP mastics exhibit the lowest φcrit (0.510) and highest C value (1.133), demonstrating the strongest interfacial interaction. COP shows intermediate interaction strength (φcrit = 0.542), yet both OP and COP outperform LP (φcrit = 0.617) in high-temperature deformation resistance within the 0.23–0.53 filler volume fraction range, evidenced by superior complex shear modulus (G*) master curves and pronounced ∆η* increases. Grey relational analysis identifies specific surface area and CaCO3 content as governing factors. Optical microscopy and FTIR confirm that filler–asphalt interactions are dominated by physical adsorption without chemical bond formation. These findings elucidate the performance advantages of both raw and calcined oyster shell powders and provide a theoretical basis for their application as sustainable high-performance bio-fillers in asphalt pavements.