Observation of two well-separated dust vortices in an unmagnetized parallel plate DC glow discharge plasma is reported in this paper. A non-monotonic radial density profile, achieved by an especially designed cathode structure using a concentric metallic disk and ring of different radii, is observed to produce double dust tori between cathode and anode. PIV analysis of the still images of the double tori shows oppositely rotating dust structures between the central disk and the ring. Langmuir probe measurements of background plasma shows a non-uniform plasma density profile between the disk and the ring. Location and sense of rotation of the dust vortices coincides with the location and direction of the radial gradient in the ion drag force caused by the radial density gradient. The experimentally observed dust vorticity matches well with the calculated one using hydrodynamic formulations with shear in ion drag dominating over the dust charge gradient. These results corroborate that a radial gradient in the ion drag force directed towards cathode is the principal cause of dust rotation.
Observation of dust cloud rotation in parallel-plate DC glow discharge plasma is reported here. The experiments are carried out at high pressures (∼130 Pa) with a metallic ring placed on the lower electrode (cathode). The dust cloud rotates poloidally in the vertical plane near the cathode surface. This structure is continuous toroidally. Absence of magnetic field rules out the possibility of E × B induced ion flow as the cause of dust rotation. The dust rotational structures exist even with water cooled cathode. Therefore, temperature gradient driven mechanisms, such as thermophoretic force, thermal creep flow, and free convection cannot be causing the observed dust rotation. Langmuir probe measurement reveals the existence of a sharp density gradient near the location of the rotating dust cloud. The gradient in the density, giving rise to a gradient in the ion drag force, has been identified as the principal cause behind the rotation of dust particles.
Measurements of local plasma parameters in dusty plasma are crucial for understanding the physics issues related to such systems. The Langmuir probe, a small electrode immersed in the plasma, provides such measurements. However, designing of a Langmuir probe system in a dusty plasma environment demands special consideration. First, the probe has to be miniaturized enough so that its perturbation on the ambient dust structure is minimal. At the same time, the probe dimensions must be such that a well-defined theory exists for interpretation of its characteristics. The associated instrumentation must also support the measurement of current collected by the probe with high signal to noise ratio. The most important consideration, of course, comes from the fact that the probes are prone to dust contamination, as the dust particles tend to stick to the probe surface and alter the current collecting area in unpredictable ways. This article describes the design and operation of a Langmuir probe system that resolves these challenging issues in dusty plasma. In doing so, first, different theories that are used to interpret the probe characteristics in collisionless as well as in collisional regimes are discussed, with special emphasis on application. The critical issues associated with the current–voltage characteristics of Langmuir probe obtained in different operating regimes are discussed. Then, an algorithm for processing these characteristics efficiently in presence of ion-neutral collisions in the probe sheath is presented.
We have explored the thermodynamics of compressed magnetized plasmas in laboratory experiments and we call these studies ‘magnetothermodynamics’. The experiments are carried out in the Swarthmore Spheromak eXperiment device. In this device, a magnetized plasma source is located at one end and at the other end, a closed conducting can is installed. We generate parcels of magnetized plasma and observe their compression against the end wall of the conducting cylinder. The plasma parameters such as plasma density, temperature and magnetic field are measured during compression using HeNe laser interferometry, ion Doppler spectroscopy and a linear ${\dot{B}}$ probe array, respectively. To identify the instances of ion heating during compression, a PV diagram is constructed using measured density, temperature and a proxy for the volume of the magnetized plasma. Different equations of state are analysed to evaluate the adiabatic nature of the compressed plasma. A three-dimensional resistive magnetohydrodynamic code (NIMROD) is employed to simulate the twisted Taylor states and shows stagnation against the end wall of the closed conducting can. The simulation results are consistent to what we observe in our experiments.
Magnetic pickup loops or B-dot probes are one of the oldest known sensors of time-varying magnetic fields. The operating principle is based on Faraday’s law of electromagnetic induction. However, obtaining accurate measurements of time-varying magnetic fields using these kinds of probes is a challenging task. A B-dot probe and its associated circuit are prone to electrical oscillations. As a result, the measured signal may not faithfully represent the magnetic field sampled by the B-dot probe. In this paper, we have studied the transient response of a B-dot probe and its associated circuit to a time-varying magnetic field. Methods of removing the oscillations pertaining to the detector structure are described. After removing the source of the oscillatory signal, we have shown that the time-integrated induced emf measured by the digitiser is linearly proportional to the magnetic field sampled by the B-dot probe, thus verifying the faithfulness of the measured signal.