The high thermopower characteristics of ionic thermoelectric cells (ITECs) significantly improve the efficiency of environmental heat and energy collection and utilization. Herein, based on the low thermal conductivity of biomass materials, we propose a novel strategy on structural design and component modulation for full component utilization and synergistic enhancement of thermodiffusion and thermogalvanic effects of single electrolytes to achieve high thermopower and output energy density. Grafting guanidinium salt ions in the chitosan gel can facilitate the selective separation of positive and negative ions of the FeCl3/2 electrolyte and enhance the thermodiffusion effect. Meanwhile, introduction of melamine in the chitosan gel enables the selective complexation/desorption of Fe3+ at cold and hot ends, which enlarges the concentration and entropy difference of redox pairs in electrolyte ions. Significant magnification of the thermocouple effect is observed, resulting in 700% increase in thermopower (−1.04 to −7.24 mV K−1). Particularly, the 90-min output energy density of the ITECs reaches 17.93 kJ m−2 at ΔT of 25 K, which is a record-breaking result among the reported quasi-solid-state ITECs. This study provides a new design pathway for development and application of high-performance ITECs.
26 August 2023 in Journal of Colloid and Interface Science
Core/shell structured composite emulsions have become an increasingly important interdisciplinary research field and deserve more attention because of their wide and potential applications in modern and advanced materials. The development of reliable synthetic and controlling approaches to composite emulsion with well-designed morphology, composition and functionality is of scientific importance and technological interest. The generation of poly(vinyl acetate)-based core/shell emulsion with phase separation can be achieved through seeded emulsion polymerisation, as well as multi-stage emulsion polymerisation. Insights on the fabrication of poly(vinyl acetate)-based core/shell latex particles with well-defined morphology and architecture have been substantially developed by recent advances in the morphological control mechanism of thermodynamics and kinetics. The factors affecting the formation of poly(vinyl acetate)-based core/shell emulsion, including polymerisation conditions, type and nature of monomer and initiator as well as grafting structure, are discussed. Finally, the properties of the poly(vinyl acetate)-based core/shell emulsion in mechanical, film-forming and adhesive performance, and its applications and potential functionalities are also briefly described.
Nitrogen- and oxygen-containing micro-mesoporous carbon microspheres (NO-MMCMs) were prepared by a self-assembly hydrothermal synthesis in the presence of m-aminophenol as a carbon and nitrogen co-precursor and block copolymer F127 as a soft template, followed by carbonization and activation with KOH. The NO-MMCMs possess a high specific surface area (up to 3203 m2 g−1), large pore volume with a well-balanced micro- and mesoporosity (up to 1.93 cm3 g−1), moderate heteroatom content (6.64 at%) and micrometer-sized sphere-like morphology. Moreover, the heteroatom contents and porosity parameters (e.g. surface area and pore volume) can be easily controlled by the carbonization temperature in the range of 600–850 °C. When tested as a supercapacitor electrode in a three-electrode system using 6 M KOH solution as the electrolyte, the typical NO-MMCMs (NO-MMCMs-600) displays a high specific capacitance (309 F g−1 at 0.1 A g−1), excellent rate capability (229 F g−1 at 20 A g−1 with capacitance retention of 74%) and outstanding cycling stability (95% capacity retention after 10 000 charge/discharge cycles at 10 A g−1). Furthermore, high performance of reversible specific capacitance of 200 F g−1 at 20 A g−1 with high rate capability of 77% can be achieved in a two-electrode cell. The superior capacitive performances may be mainly because of both the spherical morphology and the high-surface-area hierarchical microporous/mesoporous structure, which allow the rapid transport of electrolyte ions through the carbon matrix, as well as the excellent synergistic effect of co-doping of N and O. These encouraging results demonstrate that the NO-MMCMs electrode materials with high current charge and discharge capability hold great potential for supercapacitor applications, where a fast charge/discharge is required.