Polymer flooding is an important enhanced oil recovery technology introduced in field projects since the late 1960s. The key to a successful polymer flood project depends upon proper estimation of polymer retention. The aims of this paper are twofold. First, to show the mechanism of polymer flooding and how this mechanism is affected by polymer retention. Based on the literature, the mobility ratio significantly increases as a result of the interactions between the injected polymer molecules and the reservoir rock. Secondly, to provide a better understanding of the polymer retention, we discussed polymer retention types, mechanisms, factors promoting or inhibiting polymer retention, methods and modeling techniques used for estimating polymer retention.

After successful implementation for more than 6 decades by the oil and gas industry, hydraulic fracturing remains the pioneer well stimulation method to date. Polymers are one of the additives in fracturing fluids that play a significant role. Polymers are used as friction reducers and viscosifiers to provide a transport medium for proppants in fracturing fluids. There are many polymer-based fracturing fluid systems, but choosing the most appropriate type and system depends on the type of application and a wide range of parameters. Currently, there is no complete review study that gives a reference and hence a perspective for researchers on the use of polymers in hydraulic fracturing. This paper summarizes the published literature on polymers used in fracturing fluids and discusses the current research issues, efforts, and trends in the field, aiming to provide an overview of the polymer applications in slick-water and cross-linked gel systems. The mechanism and limitation of polymer use such as polymer degradation, fracture conductivity reduction, and polymer adsorption are also reviewed in this paper. The reviewed literature suggested that polymers are important additives in fracturing fluids not only to provide adequate transportation of proppants but also to determine the width of the fracture whereby higher viscosities yield wider fractures. The development of synthetic polymers and associative polymers in fracturing fluids showed a remarkable potential to improve the stability of fracturing fluids in unconventional reservoirs under reservoir conditions, which makes it an interesting topic for future studies.

A tremendous amount of water-based fracturing fluid with ancillary chemicals is injected into the shale reservoirs for hydraulic fracturing, nearly half of which is retained within the shale matrix. The fate of the retained fracturing fluid is raising some environmental and technical concerns. Mitigating these issues requires a knowledge of all the factors possibly contributing to the retention process. Many previous studies have discussed the role of shale properties such as mineralogy and capillarity on fracturing fluid retention. However, the role of some surface active agents like surfactants that are added in the hydraulic fracturing mixture in this issue needs to be understood. In this study, the influence of Internal Olefin Sulfate (IOS), which is an anionic surfactant often added in the fracturing fluid cocktail on this problem was investigated. The effect on water retention of treating two shales “BG-2 and KH-2” with IOS was experimentally examined. These shales were characterized for their mineralogy, total organic carbon (TOC) and surface functional groups. The volume of retained water due to IOS treatment increases by 131% in KH-2 and 87% in BG-2 shale. The difference in the volume of retained uptakes in both shales correlates with the difference in their TOC and mineralogy. It was also inferred that the IOS treatment of these shales reduces methane (CH₄) adsorption by 50% in KH-2 and 30% in BG-2. These findings show that the presence of IOS in the composition of fracturing fluid could intensify water retention in shale.

Copolymers of acrylamide with the sodium salt of 2-acrylamido-2-methylpropane sulfonic acid—known as sulfonated polyacrylamide polymers—had been shown to produce very promising results in the enhancement of oil recovery, particularly in polymer flooding. The aim of this work is to develop an empirical model through the use of a design of experiments (DOE) approach for bulk viscosity of these copolymers as a function of polymer characteristics (i.e., sulfonation degree and molecular weight), oil reservoir conditions (i.e., temperature, formation brine salinity and hardness) and field operational variables (i.e., polymer concentration, shear rate and aging time). The data required for the non-linear regression analysis were generated from 120 planned experimental runs, which had used the Box-Behnken construct from the typical Response Surface Methodology (RSM) design. The data were collected during rheological experiments and the model that was constructed had been proven to be acceptable with the Adjusted R-Squared value of 0.9624. Apart from showing the polymer concentration as being the most important factor in the determination of polymer solution viscosity, the evaluation of the model terms as well as the Sobol sensitivity analysis had also shown a considerable interaction between the process parameters. As such, the proposed viscosity model can be suitably applied to the optimization of the polymer solution properties for the polymer flooding process and the prediction of the rheological data required for polymer flood simulators.

Polymers are often added with water as a viscosifier to improve oil recovery from hydrocarbon reservoirs. Polymer might be lost wholly or partially from the injected polymer solution by adsorption on the grain surfaces, mechanical entrapment in pores, and hydrodynamic retention in stagnant zones. Therefore, having a clear picture of polymer losses (and retention) is very important for designing a technically and economically successful polymer flood project. The polymer adsorption and mechanical entrapment are discussed more in depth in the literature, though the effect of hydrodynamic retention can be just as significant. This research investigates the effect of the hydrodynamic retention for low and high molecular weight (AN 113 VLM and AN 113 VHM) sulfonated polyacrylamide polymer. Two high permeability Bentheimer core plugs from outcrops were used to perform polymer corefloods. Polymer retention was first determined by injecting 1 cm³/min, followed by polymer core floods at 3, 5, and 8 cm³/min to determine the hydrodynamic retention (incremental retention). A higher molecular weight polymer (AN 113 VHM) showed higher polymer retention. In contrast, hydrodynamic retention for lower molecular weight (AN 113 VLM) was significantly higher than that of the higher molecular weight polymer. Other important observations were the reversibility of the hydrodynamic retention, no permanent permeability reduction, the shear thinning behavior in a rheometer, and shear thickening behavior in core floods.

Polymers play a major role in developing rheology of fracturing fluids for multistage hydraulic fracturing horizontal wells in unconventional reservoirs. Reducing the amount of polymer adsorbed in the shale formation is essential to maintain the polymer efficiency. In this study, the ability of silica nanoparticles to minimize polymer adsorption in Marcellus shale formation at reservoir temperature was investigated. Partially hydrolyzed polyacrylamide polymers of varying molecular weights (1–12 MD), salinities (2500–50,000 ppm), polymer concentrations (100–2000 ppm), and silica nanoparticle concentrations (0.01–0.1 w/w) were used in the static adsorption experiments. Adsorption of the polymer in the Marcellus shale samples was contrasted with and without the silica nanoparticles at a Marcellus formation reservoir temperature of 65 °C, showing a significant polymer adsorption reduction of up to 50%. The adsorption and adsorption reduction were more sensitive to the variation of the polymer concentration than to the variation of the salinity within the tested conditions. The highest adsorptions were reported at the higher molecular weight of 10–12 MD. In addition, silica nanoparticles significantly improved polymer rheology at elevated temperatures. The results indicate that nanoparticles can play a significant role in reducing polymer adsorption in the fracturing fluid and improve its rheological properties and its efficiency, which will reduce the number of issues caused by the polymers in the fracturing fluid and making it more cost effective.