A novel method as proposed in the production of Calophyllum inophyllum biodiesel has been investigated experimentally. This study reports the results of biodiesel processing with electromagnetic induction technology. The applied method is aimed to compare the results of Calophyllum inophyllum biodiesel processing among conventional, microwave and electromagnetic induction. The degumming, transesterification, and esterification process of the 3 methods are measured by stopwatch to obtain time comparison data. Characteristics of viscosity, density, and fatty acid metil ester (FAME) are obtained from testing of a Gas Chromatography-mass Spectrometry (GCMS) at the Integrated Research and Testing Laboratory, Gadjah Mada University, Yogyakarta. The results present that the biodiesel produced by this method satisfies the biodiesel standards and their characteristics are better than the biodiesel produced by conventional and microwave methods. The electromagnetic induction method also offers a fast and easy route to produce biodiesel with the advantage of increasing the reaction rate and improving the separation process compared to other methods. This advanced technology has the potential to significantly increase biodiesel production with considerable potential to reduce production time and costs.
The Savonius turbine has an advantage over other types of vertical axis wind turbines (VAWT), which have speeds ranging from the lowest wind speed to the highest. However, the main problem is the negative torque on the rotary blades. This paper used computational fluid dynamics to numerically investigate the two-dimensional flow analysis of a modified elliptical Savonius wind turbine. This study investigated and compared five rotor blades: Classic, elliptical, and their three modifications. The behavior of wind energy was studied explicitly by changing the angle of the axis of the elliptical blade from the concave side, which leads to a convex shape to increase the area affected by the thrust force and increase the positive torque. The ANSYS (previously known as STASYS Structural Analysis System) Fluent version 15 software solves the unstable Reynolds-Naiver-Stokes (URAN) equation. The coupling algorithm solves the pressure-based coupling pressure velocity using the ANSYS Fluent. In the simulation, the drag, lift, and moment coefficients on the Savonius turbine were calculated directly at each change in the axis angle. The test results at wind speeds of up to nine m/s showed that the modified elliptical turbine with an axis angle of 50° had the highest coefficient power (Cp) among other elliptical blade modifications. In comparison, the test results with variations in wind speeds of 4–12 m/s showed that turbines with an axis angle of 55° performed better with a higher tip speed ratio (TSR) than other models.
30 June 2024 in Journal of Intelligent Systems and Control
Separately excited direct current (DC) motors, renowned for their linear characteristics and controllability, are extensively employed in various industrial applications. Effective speed control of these motors can be achieved through multiple methods, with fuzzy logic being a particularly robust approach. This study focuses on evaluating the transient responses of current and voltage in relation to the rotational speed of a DC motor under two distinct control schemes: field control and armature control, both subjected to similar load disturbances. A simulation-based methodology was employed using a DC motor speed control system combined with a fuzzy logic controller (FLC) designed with the Mamdani min-max method. The system was implemented in Simulink. In this framework, the FLC processes speed error signals and field current (I f) errors as inputs to generate a field voltage control signal, which is then utilized by the armature voltage (Va) regulator to modulate the armature voltage. The results demonstrate that the FLC effectively stabilizes motor speed, quickly and accurately following speed references, even under load disturbances. Moreover, the system effectively mitigates speed fluctuations induced by load variations. A comparison between the two control schemes reveals that the field control approach exhibits a slower response time, taking 2.93 seconds to reach a steady state, whereas the armature control achieves this in a significantly faster time of 0.144 seconds. These findings underscore the efficacy of fuzzy logic in maintaining stable and responsive speed control in DC motors, with the armature control method displaying superior transient performance.
21 March 2024 in Journal of Sustainability for Energy
In the quest for sustainable and environmentally friendly biofuels, Calophyllum inophyllum L., commonly known as Nyamplung, presents a promising feedstock due to its high oil content (75%) and a significant proportion of unsaturated fatty acids (approximately 71%). Notably, the oil extracted from this species exhibits higher viscosity and reduced capillarity compared to conventional kerosene, posing unique challenges for biodiesel conversion. This study explores the efficacy of electromagnetic induction heating as a novel transesterification method to produce biodiesel from Nyamplung oil. The process was optimized across a range of temperatures (45-65°C), reaction times (0.43-1.03 minutes), methanol to oil molar ratios (6:1), and a catalyst concentration of KOH at 2% of the total weight of oil and methanol. The conversion of Nyamplung oil into biodiesel was primarily assessed through the formation of methyl esters, with Gas Chromatography-Mass Spectrometry (GC-MS) employed for analytical verification. A comprehensive kinetic analysis revealed a transesterification reaction rate constant of rT=6.46×1014e(-1,068.93/RT) [ME], indicating an activation energy requirement of 1,068 kJ/mol at the operational peak temperature of 65°C. This activation energy is notably lower than that observed with microwave heating, suggesting electromagnetic induction as a more efficient heating mechanism for this reaction. The findings underscore the potential of electromagnetic induction heating in enhancing the conversion efficiency of high-viscosity feedstocks like Nyamplung oil into biodiesel, offering a promising avenue for the production of renewable energy sources. The detailed evaluation of reaction kinetics and activation energies within this study not only contributes to the optimization of biodiesel production processes but also reinforces the viability of Calophyllum inophyllum L. as a sustainable biofuel precursor.
29 March 2019 in IOP Conference Series: Materials Science and Engineering
Characteristics of magnetic-gear axial using 4 rectangular NdFeB magnetic layers mounted on acrylic disks have been studied experimentally. The goal is to reduce the use of NdFeB magnets to be more economical compared to other magnetic gear designs. The magnetic gear axial topology made was different from the magnetic gear that had been made by the previous researchers. The method used is to conduct experiments by taking comparative data between motors that are directly coupled to the generator with that using magnetic transmission gear. The results obtained show that using 4 layers of the rectangular magnet with a magnet of 258 mT can increase the magnetic torque of the gear. Comparison of torque obtained at 200 Ohm load for direct coupling is 0.19 (N-m), while for magnetic transmission gear is 0.18 (N-m).
A novel method proposed in the production of Calophyllum inophyllum biodiesel has been investigated experimentally. In this study, we report the results of biodiesel processing with electromagnetic induction technology. The method used is to compare the results of Calophyllum inophyllum biodiesel processing between conventional, microwave and electromagnetic induction. The degumming, transesterification, and esterification process of the 3 methods are measured by stopwatch to obtain time comparison data. Characteristics of viscosity, density, and Fatty Acid Metil Ester (FAME) were obtained from testing of a Gas Chromatography-mass Spectrometry (GCMS) at the Polytechnic Chemistry Laboratory of the State of Malang. The results show that the biodiesel produced by this method satisfies the biodiesel standards and their characteristics are better than the biodiesel produced by conventional and microwave methods. The electromagnetic induction method also offers a fast and easy route to produce biodiesel with the advantage of increasing the reaction rate and improving the separation process compared to other methods. This advanced technology has the potential to significantly increase biodiesel production with considerable potential to reduce production time and costs.