Weather radars have become indispensable to meteorologists and the general public for both understanding and awareness of high-impact weather events and as part of the operational warning infrastructure. In the U.S., the operational weather radar network is composed of approximately 160 WSR-88D radars, which are S-band, dish-based, polarimetric Doppler radars. This work reports on the development of a fully digital phased array weather radar that is being used to assess the potential of such technology as a replacement for the WSR-88D radars. The “Horus” radar is a truck-based, S-band, fully digital polarimetric phased array radar. Fully digital systems hold promise for meeting some of the greatest technical challenges facing the meteorological community, such as the effective integration of dual-polarization capability with phased array beam agility. This paper describes the fully digital Horus phased array weather radar that was recently completed by the Advanced Radar Research Center (ARRC) at the University of Oklahoma (OU). An overview of the advantages and challenges facing fully digital arrays for weather observations is provided along with potential mitigation strategies. Initial weather observations with Horus are given with the goal of assessing the radar scanning capabilities and most importantly the polarimetric quality. Finally, a vision for the future of next-generation weather radar operations is given with an eye toward leveraging the scalable design of Horus for high-resolution weather observations.
A substrate integrated waveguide band-reconfigurable filter with four configurations: 1) dual band; 2) low band; 3) high band; and 4) no-band, is presented. Liquid metal is chosen to enable switching between the different configurations by filling or emptying certain via holes and channels. By altering the liquid metal placement in the filter, cavity boundaries and transmission lines are adjusted to obtain the desired response. In order to demonstrate the concept, a prototype filter in C-band is designed and fabricated. The frequency responses of the liquid-metal-actuated filter (in all operating configurations) are compared with simulated and fabricated copper-plated filters. Good agreement is observed between the simulation results and the measurements. For the single- and dual-band filter configurations, insertion loss less than 1.9 dB and return loss greater than 16 dB are achieved at the center frequencies of 4.6 and 7 GHz. For the no-band (or all-stop) configuration, isolation is better than 36 dB over the entire band between 4 and 8 GHz. Additionally, to quantify the impact of using liquid metal, unloaded quality factors of a fabricated liquid-metal-actuated and copper-plated resonator are compared. The presented filter clearly demonstrates the potential of using liquid metal actuation in future reconfigurable RF hardware.
15 June 2018 in IEEE Antennas and Wireless Propagation Letters
This paper presents the design and fabrication of an orthogonal mode transducer integrated with a simple circular horn antenna. Two different approaches were used to fabricate the structure using additive manufacturing technology. In the first approach, the whole structure is printed as a single piece. To have better access to the interior layers, in the second approach, the structure is divided into two symmetric pieces, and then is fabricated. The S-parameters of both fabricated orthogonal mode transducers are measured and compared to the simulations results and discussed. Finally, the radiation patterns of the fabricated prototypes are presented and compared.
18 April 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This paper presents a low-loss fully board-integrated low-pass filter (LPF) using suspended integrated strip-line (SISL) technology. A multilayer board stack-up, with internally buried hollow cavities, is used to create the suspended strip-line. By transitioning from the top copper ground-backed coplanar waveguide trace to an internal strip-line and vice versa, a more traditional industry-standard utilization of the top copper can be realized with this SISL implementation. Based on the proposed design, an 11th-order generalized Chebyshev LPF, with a cutoff frequency of 18 GHz, has been designed and fabricated using standard printed circuit board fabrication processes. Compensated measured results show less than 1 dB of attenuation over the dc-18-GHz passband and greater than 30 dB of stopband attenuation up to 26 GHz. The proposed SISL technology LPF has advantages of low loss, compact size, and low cost, which are crucial to meet unprecedented reductions in size, weight, power, and cost (SWaP-C) of future systems.
20 June 2023 in IEEE Transactions on Microwave Theory and Techniques
In this article, a generalized theory of bandpass filtering attenuators (filtenuators) is proposed. A filtenuator is a device that combines the frequency-selective characteristics of a filter and the loss-programmable characteristics of an attenuator into a single component. The loss-programmable aspect of the filtenuator is based on the tuning of a $\pi$ -network of resistances, which are implemented using p-i-n diodes to control the individual resistance values electronically. A loss-programmable, third-order Chebyshev bandpass filtenuator is designed, fabricated, and measured to verify the generalized theory. The filtenuator is designed to operate at 1 GHz and has a tunable attenuation range of 2–10 dB. This proposed filtenuator demonstrates the feasibility of a tunable, low-cost, size, weight, and power (C-SWaP) solution to increase radio frequency (RF) system dynamic range and a design process that allows for future development of filtenuators.