The review addresses the development of the methodology of single-atom catalysts ranging from single-site to single-atom alloy systems. The preparation and characterization of single-atom catalysts and their use in a number of key catalytic reactions, including alkyne hydrogenation, are considered. The possibility of fine tuning of the surface structure of single-atom alloy catalytic systems using the adsorbate-induced segregation is analyzed for the first time. The bibliography includes 312 references.
Formation of PdIn intermetallic nanoparticles supported on α-Al2O3 was investigated by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and hydrogen temperature-programmed desorption (H2-TPD) methods. The metals were loaded as heterobimetallic Pd(μ-O2CMe)4In(O2CMe) complex to ensure intimate contact between Pd and In. Reduction in H2 at 200 °C resulted in Pd-rich PdIn alloy as evidenced by XRD and the disappearance of Pd hydride. A minor amount of Pd1In1 intermetallic phase appeared after reduction at 200 °C and its formation was accomplished at 400 °C. Neither monometallic Pd or in nor other intermetallic structures were found after reduction at 400–600 °C. Catalytic performance of Pd1In1/α-Al2O3 was studied in the selective liquid-phase diphenylacetylene (DPA) hydrogenation. It was found that the reaction rate of undesired alkene hydrogenation is strongly reduced on Pd1In1 nanoparticles enabling effective kinetic control of the hydrogenation, and the catalyst demonstrated excellent selectivity to alkene.
Volatile organic compounds (VOCs) have a negative effect on both humans and the environment; therefore, it is crucial to minimize their emission. The conventional solution is the catalytic oxidation of VOCs by air; however, in some cases this method requires relatively high temperatures. Thus, the oxidation of short-chain alkanes, which demonstrate the lowest reactivity among VOCs, starts at 250–350 °C. This research deals with the ozone catalytic oxidation (OZCO) of alkanes at temperatures as low as 25–200 °C using an alumina-supported manganese oxide catalyst. Our data demonstrate that oxidation can be significantly accelerated in the presence of a small amount of O3. In particular, it was found that n-C4H10 can be readily oxidized by an air/O3 mixture over the Mn/Al2O3 catalyst at temperatures as low as 25 °C. According to the characterization data (SEM-EDX, XRD, H2-TPR, and XPS) the superior catalytic performance of the Mn/Al2O3 catalyst in OZCO stems from a high concentration of Mn2O3 species and oxygen vacancies.
This research was focused on studying the performance of the Pd1Ag3/Al2O3 single-atom alloy (SAA) in the liquid-phase hydrogenation of di-substituted alkyne (1-phenyl-1-propyne), and development of a kinetic model adequately describing the reaction kinetic being also consistent with the reaction mechanism suggested for alkyne hydrogenation on SAA catalysts. Formation of the SAA structure on the surface of PdAg3 nanoparticles was confirmed by DRIFTS-CO, revealing the presence of single-atom Pd1 sites surrounded by Ag atoms (characteristic symmetrical band at 2046 cm−1) and almost complete absence of multiatomic Pdn surface sites (<0.2%). The catalyst demonstrated excellent selectivity in alkyne formation (95–97%), which is essentially independent of P(H2) and alkyne concentration. It is remarkable that selectivity remains almost constant upon variation of 1-phenyl-1-propyne (1-Ph-1-Pr) conversion from 5 to 95–98%, which indicates that a direct alkyne to alkane hydrogenation is negligible over Pd1Ag3 catalyst. The kinetics of 1-phenyl-1-propyne hydrogenation on Pd1Ag3/Al2O3 was adequately described by the Langmuir-Hinshelwood type of model developed on the basis of the reaction mechanism, which suggests competitive H2 and alkyne/alkene adsorption on single atom Pd1 centers surrounded by inactive Ag atoms. The model is capable to describe kinetic characteristics of 1-phenyl-1-propyne hydrogenation on SAA Pd1Ag3/Al2O3 catalyst with the excellent explanation degree (98.9%).