The height of tree stumps following mechanized forest operations can be influenced by machine-, tree-, terrain-, and operator-related characteristics. High stumps may pose different economic and technical disadvantages. Aside from a reduction in product recovery (often associated with sawlog potential), leaving high stumps can complicate future entries if smaller equipment with low ground clearance is used, particularly in the case where new machine operating trails are required. The objective of this exploratory study was to examine if correlations existed between the height of tree stumps following mechanized harvesting and the shape of the above-ground root collar, stump diameter, and distance to the machine operating trail. In total, 202 sample stumps of Norway spruce (Picea abies (L.) Karst.) and the surrounding terrain were scanned with a terrestrial laser scanner. The collected data was processed into a 3D-model and then analyzed. Stump height was compared with different characteristics such as stump diameter at the cut surface, distance to the machine operating trail, number of visible root flares per stump, and the root collar. The number of root flares per stump had a positive influence on stump diameter and height, showing a general trend of increasing diameter and height with the increasing number of root flares. Root angles also had an influence on the stump diameter. The diameter of a stump and the shape of the root collar at the cut surface together had a significant effect on stump height and the model reported explained half of the variation of stump heights. Taken together, these findings suggest that other factors than the ones studied can also contribute in influencing stump height during mechanized harvesting operations. Further investigations, including pre- and post-harvest scans of trees selected for removal, are warranted.

It is common to have large trees in mature hardwood-dominated stands. This is especially true for European beech (Fagussylvatica L.), which can also have a complex architecture. Such trees have predominantly been harvested using motor-manual operations. However, in an effort to increase occupational safety and allow for a more continuous wood flow to processing facilities, fully-mechanized systems are also being employed more frequently. This study was established to determine the effect of season (Fall or Winter) and harvester type (wheeled or tracked) on the performance of semi- and fully- mechanized harvesting systems deployed in beech-dominated stands. Time-and-motion analysis was conducted on a total of 927 trees located in two forest sites in Germany. The study indicated that new silvicultural prescriptions make it impossible to harvest all trees exclusively with mechanized systems, even in the case of the tracked harvester with its 14.5 m boom. Motor-manual intervention was needed with trees that were too large, malformed or out of reach. Motor-manual intervention was significantly more frequent for the wheeled (30%) than for the tracked harvester (18%). Once again, tree size had the strongest effect on time consumption in a linear model, which varied from 0.5 to over 6 min per tree. Season and machine effect were also significant but could only account for a small fraction of the total variability. For the same tree size, time consumption was higher with the wheeled harvester and during the fall. The model also indicated a significant relationship between tree form and time consumption, even though the explanatory contribution of this independent variable was relatively small, too. Good stem form resulted in a lower time consumption. The larger tracked harvester was generally more efficient, but also more expensive to own and operate: its higher costs must be weighed against the higher revenues. New silvicultural trends make it difficult to achieve full mechanization, but the results of this study may guide managers towards technical solutions that minimize motor-manual intervention to the advantage of higher productivity and better occupational safety.

Fully mechanized hardwood operations usually rely on manual bucking, which may decrease potential volume and value recovery as compared to automatic bucking. This study aimed at evaluating bucking done in cut-to-length (CTL) operations, hypothesizing a possible increase of value recovery by using a bucking optimizer. Evaluation of bucking was done by a comparison of actual bucking with a mathematical solution – BuckR – a bucking optimizer based on dynamic programming. Results showed that the mathematical approach significantly outperformed manual bucking when quality was not considered, and only main stem products were included. Throughout 315 study trees (Acer saccharum, Acer rubrum, and Betula alleghaniensis) located in the Acadian forests of Eastern Canada, a mean increase of 112% in value and 84% in volume recovery per tree was reached through mathematical optimization. Contributions of mathematical bucking can be summarized by 1) a significantly higher number of sawlogs and a greater mean log length of sawlogs and pulp logs, 2) a two-fold increase in processed height, and 3) a considerable reduction in minimal diameters as compared to actual bucking. Those results illustrate the possibility to increase value and volume recovery in mechanized CTL operations and therefore to utilize the wooden resource more efficiently.