Ultra-high-molecular-weight polyethylene (UHMWPE) fiber laminate is currently widely used in ballistic protection for its exceptional physical and mechanical properties. However, the dynamic compressive mechanism of UHMWPE laminate remains poorly understood. Therefore, the stress–strain relationship, the influence of different thickness, area, and shape, and the maximum stress and fracture stress are studied in both out-of-plane and in-plane directions under quasi-static and dynamic loading using a universal test machine, Split Hopkinson pressure bar (SHPB), and high-speed camera. Furthermore, numerical models with cohesive elements are developed. The results indicate a dependency on strain rate and loading direction. Firstly, the stress–strain curve of dynamic testing can be divided into different zones according to different loading directions and strain rates. Secondly, with the increase of the strain rate in the dynamic testing, the maximum stress and fracture stress increase as well; relatively speaking, the fracture stress in the out-of-plane direction is greater than the fracture stress in the in-plane direction. Thirdly, both experiment and simulation indicate that the thickness does not influence the modulus clearly the in out-of-plane direction but influences the modulus in the in-plane direction. Fourthly, the fracture stress of dynamic testing is higher than the fracture stress of quasi-static testing in both directions. Finally, the numerical results show good agreement with the experiment in terms of the maximum stress and failure form.
1 January 2020 in Latin American Journal of Solids and Structures
This work focused on the stress response of anisotropic 30SiMn2MoVA steel gun barrel under coupled thermo-mechanical loads, namely, the contact pressure and friction of projectile, thermal load and pressure of propellant gas. The effect of temperature on the mechanical properties of gun barrel was considered. Two thermal-displacement coupled finite element models (FEM) were built by ABAQUS software. The first was the interaction model of projectile and barrel which was to calculate the stress of barrel engraved by copper jacket and steel jacket projectile. The results of barrel in the interaction model, as an initial condition, were imported to the second FEM which was applied with thermal load and pressure of propellant gas. The results show that the rifling at chamber throat has the largest stress and circumferential stress under coupled loads. It gives a request that the gun barrel should have the better circumferential mechanical properties. The plastic deformation of the rifling at the chamber throat is observed which indicates that 30SiMn2MoVA gun barrel has a low service life due to the poor mechanical properties.
This paper established three simulation models of the typical 5.8 mm small caliber firearm and evaluated the validity of the model. The three models adopted different geometric models and loading methods. Experimental verification is conducted for the numerical models. The muzzle velocity of the bullet, vibration of barrel, posture of the bullet of the experiment and simulation were compared and analyzed. And the accuracy of the models is evaluated. The calculation results of the three models were evaluated which included velocity of bullet, relative swing angle of bullet, simulation calculation time and pressure of barrel inner wall. The results indicated that these three models could be used in different scenarios as required. When only the motion of the bullet in the chamber is studied, the analysis can be carried out using Model no. 1 with simple barrel and load method, which has a shorter computational time. Model no. 2 takes into account the actual effect of propellant gas pressure in the barrel and is suitable for the study of the inner wall of the barrel. Model no. 3 is the closest to the actual gun situation and is suitable for considering the study of gun system. Combined with the calculation time and simulation results, the three models can have different application scenarios.
1 January 2024 in Latin American Journal of Solids and Structures
The characteristics of a bullet are closely related to its shooting accuracy. In actual shooting, the centroid and entry angle of the bullet always deviate from the ideal state. To study the influence of these two parameters on the movement of the bullet, a finite element model of the bullet movement inside the barrel was built based on a 5.8 mm small-caliber rifle to simulate the actual process of firing bullets. In this model, the pressure load of the real gunpowder gas on the bullet was considered. This model was also verified by experiments and the relative error is less than 1.5%. The result shows that the influence the centroid and entry angle of the bullet are mainly reflected in the amplitude and phase angle of the bullet swing angle. The larger the offsetting distance of cetroid is, the amplitude of the pitch and yaw angle are. The maximum magnitude of amplitude is 0.2°. The difference of swing angle in phase is equal to the difference in offsetting angle. The curve characteristics of different deviation angle are similar to the curve of bullet cetroid effect. The range of the pitch angle is -1°~0.9° and the range of the yaw angle is -0.9°~0.9°.