Shuaixu Chun

Dr. Shuaixu Chun


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 May 2026 in Materials
Verified
Journal Article
Open access
PDF file
SCShuaixu Chun
Shuaixu Chun
HNHaifeng Nie
Haifeng Nie
XGXiaoyang Guo
Xiaoyang Guo
TCTihao Cao
Tihao Cao
QRQuanxing Ren
Quanxing Ren
YLYinsheng Li
Yinsheng Li
Reaction-bonded SiC (RBSC) ceramics exhibit limited hydrothermal corrosion resistance due to the presence of residual silicon. This study presents a strategy to enhance the corrosion resistance of RBSC through homogeneous incorporation of MoSi2 and concurrent reduction in residual silicon content. Three material systems were fabricated via reactive melt infiltration: conventional RBSC with a SiC/C preform (SC), a SiC–MoSi2 composite incorporating commercial Mo2C powder via physical mixing (MC), and a SiC–MoSi2 composite derived from a Mo2C/C precursor synthesized by a molten salt method (MS). The Mo2C/C composite synthesized at 1150 °C exhibited fine, uniformly distributed Mo2C particles coated on carbon black, contrasting with the agglomerated distribution in commercial Mo2C mixtures. During reactive sintering at 1600 °C, Mo2C reacted with molten Si to form MoSi2, reducing residual Si content. Sample MS achieved the lowest residual Si (8.77 ± 0.45 vol.%), followed by MC (12.43 ± 0.86 vol.%) and SC (19.17 ± 1.01 vol.%). All samples achieved near-full densification (open porosity < 0.1%), with bulk densities of 2.96 ± 0.05, 3.03 ± 0.03, and 3.07 ± 0.03 g/cm3 for SC, MC, and MS, respectively. Microstructurally, MS displayed homogeneous MoSi2 dispersion, while MC showed partial MoSi2 aggregation, and SC contained continuous residual Si regions. Hydrothermal corrosion tests at 345 °C and 15 MPa for 9 days demonstrated that corrosion resistance followed the order MS > MC > SC. After 9 days, weight loss was 22.3970 ± 1.2059 mg/cm2 (SC), 17.6370 ± 0.8266 mg/cm2 (MC), and 15.4347 ± 0.7807 mg/cm2 (MS), with corrosion depths of 393.17 ± 27.46, 267.40 ± 24.44, and 224.60 ± 25.13 μm, respectively. The enhanced performance of MS arises from two synergistic factors: reduced residual Si minimizes large corrosion pores, while uniform distribution of MoSi2 facilitates the formation of a stable, dissolution-resistant composite oxide layer composed of MoO3 and SiO2, in which MoO3 restrains excessive dissolution of SiO2 through a pinning effect. These findings demonstrate that combining residual Si reduction with homogeneous MoSi2 incorporation via molten salt-synthesized precursors offers an effective strategy for improving hydrothermal corrosion resistance of reaction-bonded SiC-based materials for applications in high-temperature and high-pressure aqueous environments such as nuclear water reactors.

23 April 2026 in Materials
Verified
Journal Article
Open access
PDF file
XGXiaoyang Guo
Xiaoyang Guo
SCShuaixu Chun
Shuaixu Chun
HNHaifeng Nie
Haifeng Nie
XPXuxin Ping
Xuxin Ping
JYJingchen Yuan
Jingchen Yuan
YLYinsheng Li
Yinsheng Li
To address the increasing demands for lightweight, high-temperature resistant braking materials under extreme service conditions, a novel Cf/SiC-B12(C,Si,B)3 composite was developed in this work. The composite was fabricated via a hybrid slurry infiltration-reactive melt infiltration (SI-RMI) process. The tribological performance under coupled temperature–velocity conditions was systematically evaluated using a ball-on-disk tester over temperatures from 25 to 600 °C (at 900 r/min) and sliding speeds from 300 to 900 r/min (at 600 °C). The results indicate that temperature dominates the friction and wear behavior. At room temperature, the composite exhibits a friction coefficient of 0.52 and a wear rate of 4.019 × 10−4 mm3/(N·m). With increasing temperature, friction coefficients decreased to 0.43 at 400 °C and 0.41 at 600 °C, while wear rates increased sharply to 12.025 × 10−4 mm3/(N·m) at 400 °C before declining to 5.228 × 10−4 mm3/(N·m) at 600 °C. Under the fixed temperature of 600 °C, raising rotational speed from 300 to 900 r/min increased the wear rate only marginally (4.953 to 5.228 × 10−4 mm3/(N·m)). Surface analysis indicates that a continuous Si-B-O oxide layer (mainly SiO2 and B2O3) forms at 600 °C, which may provide solid lubrication and oxidation resistance. The present work offers a preliminary exploration of the tribological evolution and self-lubrication mechanisms of Cf/SiC-B12(C,Si,B)3 composites, providing potential insights for the design of advanced ceramic-matrix braking materials.