Maryamsadat Tahavori

Prof. Dr. Maryamsadat Tahavori


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 November 2017 in IEEE Access
Verified
Journal Article
Open access
RDRahman Dashti
Rahman Dashti
MDMohammad Daisy
Mohammad Daisy
Hamid Reza ShakerHamid Reza Shaker
Hamid Reza Shaker
MTMaryamsadat Tahavori
Maryamsadat Tahavori
Fault location techniques play an essential role in system recovery and repair. Therefore, numerous methods have been presented for fault location in power transmission and distribution networks. The contribution of this paper is to extend the state-of-art impedance-based fault location methods to support four-wire power distribution. To make this possible an algorithm is developed. The method is obtained using principles of circuit theory and overcomes the challenges which prevent use of most fault location methods for distribution networks in practice. The paper presents the detailed equations which are used in the algorithm and how they are obtained. The satisfactory performance of the algorithm is confirmed with numerical examples using MATLAB software.

2 January 2023 in IEEE Access
Verified
Journal Article
Open access
AHAgus Hasan
Agus Hasan
MTMaryamsadat Tahavori
Maryamsadat Tahavori
HMHenrik Skov Midtiby
Henrik Skov Midtiby
In this paper, three model-based fault diagnosis algorithms for robotic systems are designed, compared, simulated, and implemented. The first algorithm is based on a nonlinear adaptive observer (NLAO), where a sufficient condition for the convergence of the estimator is derived in terms of linear matrix inequality (LMI) under persistence of excitation condition. The second algorithm is based on an adaptive extended Kalman filter (AEKF). Unlike traditional approaches, where the fault parameters are considered as augmented state variables, the AEKF directly estimates the fault parameters from measurement data. The third algorithm is based on a cascade of a nonlinear observer (NLO) and a linearized adaptive Kalman filter (LAKF), called the adaptive exogenous Kalman filter (AXKF). The pros and cons for each algorithm are discussed. The performance of the algorithms is compared in a single-link joint robot system. Furthermore, the algorithms are implemented in a ball-balancing robot to detect and estimate the magnitude of the actuator faults.

20 December 2013 in IEEE Transactions on Automatic Control
Verified
Journal Article
Closed access
Hamid Reza ShakerHamid Reza Shaker
Hamid Reza Shaker
MTMaryamsadat Tahavori
Maryamsadat Tahavori
In this technical note, a new method for model reduction of bilinear systems is presented. The method is developed in particular for many applications in which one is interested to approximate a system in a given frequency-interval. To this end, new generalized frequency-interval gramians are introduced for bilinear systems. It is shown that these gramians are the solutions to the so-called frequency-interval generalized Lyapunov equations. The conditions for these equations to be solvable are derived and an algorithm is proposed to solve such equations iteratively. The method is further illustrated with the help of an illustrative example. The numerical results show that the method is more accurate than its previous counterpart which is based on the ordinary gramians.

16 July 2012 in Journal of Vibration and Control
Verified
Journal Article
Closed access
PDF file
Hamid Reza ShakerHamid Reza Shaker
Hamid Reza Shaker
MTMaryamsadat Tahavori
Maryamsadat Tahavori
Accurate and reliable process measurements play a key role in the success of process control. In addition to selecting the instrumentation hardware, it is important to determine which variables should be measured in a process. Therefore it is important to study techniques for placing sensors on the processes. Dually the problem of placing actuators on the processes is equally important. In this paper, the problem of determining optimal sensor and actuator locations for the linear systems is addressed. The problem of the sensor locations is viewed as the problem of maximizing the output energy generated by a given state and for the actuator locations is viewed as the problem of minimizing the input energy required to reach a given state. Such design problems occur in many applications, and therefore have been studied extensively. Unfortunately, the results in this context, which have been proposed so far, only support stable systems. However, in industrial practices it is often the case that the system, which is needed to be controlled, is not stable. The method which is proposed in this paper is a general method in the sense that it supports both stable and unstable systems. The technique is successfully used for determining the optimal sensor locations of the linearized Continuous Stirred-Tank Reactor unstable model.

21 February 2014 in International Journal of Control
Verified
Journal Article
Closed access
Hamid Reza ShakerHamid Reza Shaker
Hamid Reza Shaker
MTMaryamsadat Tahavori
Maryamsadat Tahavori

28 July 2014 in International Journal of Control
Verified
Journal Article
Closed access
Hamid Reza ShakerHamid Reza Shaker
Hamid Reza Shaker
MTMaryamsadat Tahavori
Maryamsadat Tahavori
Decentralised and partially decentralised control strategies are very popular in practice. To come up with a suitable decentralised or partially decentralised control structure, it is important to select the appropriate input and output pairs for control design. This procedure is called control configuration selection. It is well known that a suitable control configuration selection is an important prerequisite for a successful industrial control. In this paper the problem of control configuration selection for multiple-input and multiple-output (MIMO) bilinear processes is addressed. First, the concept of the cross-gramian is developed for bilinear systems. The conditions for the existence of generalised cross-gramian are derived. It is shown that if the cross-gramian exists it is the solution to the generalised Sylvester equation. To obtain the cross-gramian in a more computationally efficient way, an iterative method for solving the generalised Sylvester equation is proposed. The generalised cross-gramian is used to form the generalised Hankel interaction index array. The generalised Hankel interaction index array is used for control configuration selection of MIMO bilinear processes. Most of the results on control configuration selection, which have been proposed so far, can only support linear systems. The proposed method supports bilinear processes, takes the effects of dynamics of the process into account and can be used to propose a richer (sparse or block diagonal) controller structure. More importantly, since for each element of generalised Hankel interaction index array just one generalised Sylvester equation is needed to be solved, the proposed control configuration selection method is computationally more efficient than its gramian-based counterparts.