This paper utilizes ANSYS-AQWA hydrodynamic simulation analysis software (2022 R2) to investigate the wave dissipation performance of an Oscillating Water Column (OWC) perforated floating breakwater under irregular wave conditions. The study examines the effect of spacing, width of the OWC opening, water depth, incident wave angle, and significant wave height on the wave dissipation performance of the floating breakwater. The results indicate that the wave dissipation performance of the OWC-perforated floating breakwater surpasses that of similar structures. The transmission coefficient is significantly influenced by spacing and water depth when subjected to irregular waves. The width of the OWC opening also affects the wave dissipation to some extent, with wider openings demonstrating improved performance in the case of long-period waves. The incident wave angle of 0 degrees yields enhanced wave dissipation performance. Although the meaningful wave height has minimal impact on wave dissipation, it increases proportionally with the rise in meaningful wave height. This study offers valuable insights for the design and implementation of floating breakwaters and holds significant practical implications for the research on integrated devices combining floating breakwaters and wave power generation.
This study presents novel analytical solutions for analyzing wave dissipation effect and bottom flow field characteristics of permeable submerged horizontal plates through physical model trials. The experimental results show that a solid submerged horizontal plate effectively attenuates wave cycles, with a greater periodic attenuation effect at smaller submerged depths. However, this attenuation effect becomes reduced or less pronounced after a certain threshold. Selecting an optimal opening ratio becomes key to achieving the desired cycle attenuation. When the inundation depth of the horizontal plate is large, the wave dissipation effect is weak. Reducing the opening rate can improve the wave dissipation effect, but only to a certain extent. Under irregular wave actions, the velocity field of the submerged horizontal plate is uniformly distributed. The relative submerged depth has minimal effect on the maximum flow velocity and root mean square flow velocity. Increasing the wave height and increasing the open holes on a plate can improve the flow velocity at the bottom of the plate. However, increasing the opening ratio also leads to insignificant changes in flow velocity. A correlation between the transmission coefficient of the open plate and the maximum flow velocity has also been determined. The findings of this paper serve as a research foundation for the implementation of submerged horizontal plate wave dissipation structures in engineering.
1 January 2018 in Advances in Materials Science and Engineering
The damage process is accompanied by the acoustic emission for quasibrittle materials. And in the process of material damage evolution, the length of microcracks satisfies the fractal distribution. Research on their relationship in theory is helpful to reveal the law of material damage evolution and acoustic emission activities. Damage variable expressions are proposed based on the damage and fractal characteristics firstly. Then, the statistical models for acoustic emission considering damage and fractal characteristics are established by deducing the relationship between acoustic emission parameters and load cycles and fractal dimensions. The effects of damage and fractal effects on acoustic emission parameters are analyzed finally. The results show that the damage accelerates the AE activity to the rougher material, the opposite to the more homogeneous material. It can also be seen that the increase of the fractal dimension, the homogeneity constant m, will substantially increase the AE activities.
26 June 2017 in DEStech Transactions on Engineering and Technology Research
As being a typical multi-freedom degree system structure, self-anchored cablestayed suspension bridge is significantly affected by higher modes in the earthquake response. Traditional force-based pushover analysis of reverse triangle or uniform distribution patterns will lead* to a certain error for the results of pushover analysis of self-anchored cable-stayed suspension bridge. An improved method of displacement-based mode pushover analysis is presented in this paper by combining the two stage horizontal displacement pattern with mode pushover. This improved method can take the contributions of higher modes into account. And the applicability of the method can be verified commendably by the selected examples. Traditional force-based pushover analysis considers the seismic load is equivalent to lateral load. And it judges whether the deformation ability of the structure and component can meet the need of design and use function by analysing nonlinear response of structures under the monotonic increasing horizontal lateral load applied to the structure with a certain distribution mode. The selection of the lateral load distribution mode can directly affect the analysis results of the pushover method on the seismic performance of whole structure in traditional force-based pushover analysis. Moreover, the problem of stiffness degradation after failure is not taken into account in this traditional wide application method. Seismic hazard, experiment and theoretical analysis indicate structural collapse is mainly due to the lack of deformation capacity and energy dissipation capacity during severer earthquake. In this case, the deformation capacity and the displacement response of structure will have an certain impact on the damage degree of structural members. Therefore, it is more reasonable to use displacement control on structural seismic response during severer earthquake[4]. Compared with the traditional force-based design, the displacement of structure can reflect the nonlinear reactive state more during severer earthquake, it also can control the behavior of structure better in earthquake. Consequently, the displacement-based seismic design method has been greatly developed[5-10]. There are three commonly used displacement-based seismic design method: ductility factor design, capacity spectrum and direct displacement-based design method. The basic thought of displacement-based mode pushover analysis is as follows: first, put monotonic increasing lateral displacement to bear on structure directly according to a certain horizontal displacement distribution mode, second, the final failure pattern of structure is obtained by pushover the structure to the target displacement, after that, whether the deformation ability of structure and component can meet the need of design and use function can be analyzed.