Yuhan Yin

Ms. Yuhan Yin


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 June 2026 in Drones
Verified
Journal Article
Open access
PDF file
XLXiaoyi Liu
Xiaoyi Liu
YYYuhan Yin
Yuhan Yin
KWKunxiao Wu
Kunxiao Wu
YZYetong Zhang
Yetong Zhang
JZJianyong Zheng
Jianyong Zheng
FMFei Mei
Fei Mei
To address the problems of closed-loop task organization, strong corridor constraints, and path failure after local disturbances in unmanned aerial vehicle (UAV) inspection of gas-insulated switchgear (GIS) rooms, this paper proposes a topology-and-corridor-guided bias-suppressed D* (TCG-BS-D*) method for closed-loop three-dimensional (3D) path planning and local replanning. The proposed method constructs a structured guidance model based on the inspection-corridor topology, generates local 3D path segments according to a predetermined inspection sequence, and forms a nominal closed-loop inspection path through bias suppression and path regularization. Meanwhile, for local maintenance blockage and dynamic disturbance scenarios, an alternative local replanning strategy is applied to the affected path segments. Simulation results show that, under the static closed-loop inspection condition, the proposed method achieves a total path length of 700.22 m, a total inspection time of 269.32 s, an average safety clearance of 8.18 m, 37 large-angle turns, a corridor adherence rate of 80.73%, and a task completion rate of 100%, showing superior performance in inspection efficiency, safety margin, trajectory regularity, and corridor consistency. Under the local blockage condition, the replanned path introduces path-length and time increments of 71.29 m and 25.88 s, respectively, while maintaining the minimum safety clearance at 1.52 m and increasing the corridor adherence rate to 83.91%. Under dynamic disturbance conditions, the minimum dynamic safety clearance is improved from −2.71 m to 17.84 m, effectively eliminating the local dynamic collision risk. The results demonstrate that the proposed method can balance closed-loop path-generation efficiency, corridor-structure consistency, safety margin, and adaptability to local disturbances, providing an effective solution for UAV inspection path planning in GIS rooms.

28 April 2026 in Electronics
Verified
Journal Article
Open access
PDF file
XLXiaoyi Liu
Xiaoyi Liu
YYYuhan Yin
Yuhan Yin
YZYetong Zhang
Yetong Zhang
KWKunxiao Wu
Kunxiao Wu
JZJianyong Zheng
Jianyong Zheng
FMFei Mei
Fei Mei
To address the challenges of insufficient safety, poor trajectory executability, and low stability of online optimization in UAV inspection path planning for converter valve halls under conditions of dense obstacles, narrow passages, and complex electromagnetic environments, an electromagnetic risk-aware three-dimensional path planning method based on model predictive path integral (MPPI) is proposed. Considering the typical “valve-tower array–bushing” layout in converter valve halls, a three-dimensional obstacle model consisting of prismatic valve towers and cylindrical bushings is established. A comprehensive cost function is then constructed by jointly incorporating path length, safety clearance, trajectory smoothness, and electromagnetic risk. On this basis, an electromagnetic risk term, a corridor guidance term, and a control increment regularization term are integrated into the MPPI receding-horizon optimization framework to enable online generation of inspection trajectories. Simulation results demonstrate that, compared with A*, Vanilla MPPI, and Corridor MPPI, the proposed method generates smoother and safer trajectories and achieves superior overall performance in terms of total cost, minimum clearance, success rate, and mean tracking error. The proposed method provides an effective solution for intelligent UAV inspection path planning in converter valve halls.

28 March 2026 in Sensors
Verified
Journal Article
Open access
PDF file
YYYuhan Yin
Yuhan Yin
XLXiaoyi Liu
Xiaoyi Liu
KWKunxiao Wu
Kunxiao Wu
RXRuilin Xu
Ruilin Xu
JZJianyong Zheng
Jianyong Zheng
FMFei Mei
Fei Mei
To address the challenges of small targets, severe background clutter, and high deployment cost in UAV-based power-line defect detection, this paper proposes a lightweight defect detection model based on an improved YOLOv8n. In the downsampling stage, we design an improved lightweight adaptive downsampling module (ADownPro) to replace part of conventional convolutions, which uses a dual-branch parallel structure for stronger feature interaction and depthwise separable convolutions (DSConv) for complexity reduction. In the feature extraction stage, an integration of cross-stage partial connections and partial convolution (CSPPC) is proposed to replace the C2F module for efficient multi-scale feature fusion. In the detection head, mixed local channel attention (MLCA), which combines channel-spatial information and local–global contextual features, is introduced to strengthen defect-focused representations under complex backgrounds. For the loss function, a scale-annealed mixed-quality EIoU loss (SAMQ-EIoU) is proposed by combining iso-center scale transformation, scale factor annealing and focal-style quality reweighting to improve localization accuracy at high IoU thresholds. Experiments on a constructed dataset covering six typical defect categories show that the improved YOLOv8n achieves 91.4% mAP@0.50 and 64.5% mAP@0.50:0.95, with only 1.59 M parameters and 4.9 GFLOPs. Compared with mainstream detectors, the proposed model achieves a better balance between detection accuracy and lightweight design. In particular, compared with the recently proposed YOLOv8n-DSN and IDD-YOLO, it improves mAP@0.50 by 0.6% and 0.8%, and mAP@0.50:0.95 by 1.2% and 4.8%, respectively, while further reducing the parameter count by 1.00 M and 1.26 M, and the FLOPs by 1.7 G and 0.2 G. Moreover, the cross-dataset evaluation on the public UPID and SFID datasets further demonstrate the robustness and generalization ability of the proposed method.

15 May 2026 in Sensors
Verified
Journal Article
Open access
PDF file
XLXiaoyi Liu
Xiaoyi Liu
YYYuhan Yin
Yuhan Yin
KWKunxiao Wu
Kunxiao Wu
YZYetong Zhang
Yetong Zhang
JZJianyong Zheng
Jianyong Zheng
FMFei Mei
Fei Mei
To address the challenges of significant vehicle parking constraints, limited UAV endurance, and insufficient multi-task coordination efficiency in distribution network inspection, this paper proposes a vehicle–UAV synchronous cooperative inspection task scheduling method based on multi-objective twin delayed deep deterministic policy gradient and nondominated sorting genetic algorithm II (MOTD3-NSGA-II). First, a vehicle–UAV synchronous cooperative inspection model is established by considering staged vehicle repositioning, same-site UAV launch, landing, and retrieval, as well as state-of-charge constraints. On this basis, a multi-objective optimization model is formulated with task coverage, mission completion time, minimum residual state of charge, and load balance as objectives. Then, a bi-level closed-loop solution framework is developed, in which NSGA-II is employed to optimize cooperative parameters and objective preference weights, while the inner-layer MOTD3 learns UAV scheduling policies in a continuous action space. Finally, the proposed method is validated in four simulation scenarios with different task scales and spatial distribution characteristics. The results show that 100% task coverage is achieved in all four scenarios, with mission completion times of 11,109 s, 9693 s, 10,538 s, and 10,721 s, respectively, while the minimum residual state of charge is maintained within 0.28–0.36. The results demonstrate that the proposed method can balance inspection completeness, execution efficiency, energy safety, and cooperative stability, providing a useful reference for intelligent task scheduling in vehicle–UAV cooperative distribution network inspection.

29 July 2026 in Technologies
Verified
Journal Article
Open access
PDF file
YYYuhan Yin
Yuhan Yin
XLXiaoyi Liu
Xiaoyi Liu
KWKunxiao Wu
Kunxiao Wu
JZJianyong Zheng
Jianyong Zheng
To address the sampling misalignment and detail loss caused by fixed-grid downsampling for small-scale defects, as well as the insufficient differentiated modeling and interaction of defect details and structural context in UAV-acquired power-line images, an enhanced lightweight YOLOv8n-based framework for power-line defect detection is developed. First, a content-adaptive downsampling (CAD) module is developed to predict input-dependent sampling offsets and normalized aggregation weights and to perform differentiable resampling. Combined with local-global interactive depthwise separable convolution, CAD improves the preservation of small-object details while maintaining relatively low computational complexity. Second, a dynamic subspace gated exchange (DSGE) module is proposed to adaptively partition features into a high-frequency detail subspace and a low-frequency structural subspace according to the input content. Heterogeneous branches and bidirectional gated exchange are then employed to jointly model fine-grained details and structural context. In addition, the lightweight mixed local channel attention (MLCA) mechanism is incorporated in the detection head as an auxiliary feature-enhancement component. Experimental results show that the proposed model achieves mAP@0.50 and mAP@0.50:0.95 values of 92.3% and 62.9%, respectively, outperforming the compared models under the current evaluation protocol. With 1.90 M parameters and 5.6 G FLOPs, the model reaches an inference speed of 134.7 FPS on the desktop GPU platform, demonstrating that content-adaptive sampling and dynamic detail–structure interaction can improve small-defect detection and complex-background suppression while maintaining relatively low model complexity.

12 June 2026 in Technologies
Verified
Journal Article
Open access
PDF file
XLXiaoyi Liu
Xiaoyi Liu
YYYuhan Yin
Yuhan Yin
YZYetong Zhang
Yetong Zhang
KWKunxiao Wu
Kunxiao Wu
JZJianyong Zheng
Jianyong Zheng
FMFei Mei
Fei Mei
Extreme weather conditions impose significant challenges on distribution network inspection because UAV flight safety, energy consumption, vehicle mobility, and task coverage are strongly coupled under wind disturbances. To improve inspection efficiency and operational robustness, this paper proposes a weather-aware asynchronous vehicle–UAV cooperative scheduling method based on bi-level MODDPG–NSGA-II optimization. First, a dynamic wind field model and a wind-sensitive UAV energy model are established to describe the effects of background wind, vertical wind shear, and local gust disturbances on UAV motion and state-of-charge evolution. Then, an asynchronous vehicle–UAV collaboration mechanism is developed, allowing the vehicle to move toward downstream parking sites after UAV deployment while UAVs perform inspection and cross-site recovery under rendezvous and energy safety constraints. On this basis, a bi-level optimization framework is constructed, in which NSGA-II searches global coordination parameters and MODDPG learns adaptive multi-UAV scheduling policies in continuous decision spaces. Controlled wind-factor experiments show that, with the task scale fixed at 52 inspection tasks, the proposed method maintains 100% task coverage under 0–10 m/s wind conditions. As the reference wind speed increases from 0 m/s to 10 m/s, the mission completion time increases from 40.97 min to 70.24 min, while the minimum residual SOC decreases from 50.32% to 13.82%, which remains above the predefined safety threshold. Repeated stochastic trials and statistical significance analysis further indicate that the proposed method achieves shorter mission time and more stable task coverage than representative baselines under the same experimental conditions. The scope of this study is simulation-level validation; real-world flight tests and hardware-in-the-loop verification will be further investigated in future work.