Yang Li

Dr. Yang Li


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 February 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
YZYingming Zhang
Yingming Zhang
BHBinkui Hou
Binkui Hou
QWQian Wang
Qian Wang
YLYang Li
Yang Li
ZHZhigao Huang
Zhigao Huang

30 November 2025 in Advanced Science
Verified
Journal Article
Open access
CLChenyi Li
Chenyi Li
HGHanxiao Gao
Hanxiao Gao
YGYutie Gong
Yutie Gong
YLYen-Ting Lin
Yen-Ting Lin
YLYuquan Liu
Yuquan Liu
HZHuamin Zhou
Huamin Zhou
Polymer‐based film capacitors with ultrafast rates are extensively used in modern electronics and electric power systems. Dielectric polymers typically exhibit a low dielectric constant, while their energy density at elevated temperatures is limited by drastically increased conduction. To address this challenge, it is reported that proton irradiation enables concurrently enhanced dielectric constant and energy storage properties at high temperatures. The combined atomic force microscopy‐infrared spectroscopy and first‐principles calculations reveal that proton irradiation facilitates local rotation of ether bonds in aromatic polymers, producing greatly increased local polar states leading to markedly improved polarizability while preserving dense chain packing. Consequently, an ultrahigh discharged energy density of 6.9 J cm −3 with an efficiency > 95% is achieved in irradiated poly(ether imide) at 150 °C, exceeding current dielectric polymers and nanocomposites. The results suggest an alternative postprocessing method toward rational design of high‐performance dielectrics for capacitive energy storage.

23 October 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
ZHZhangyong Hu
Zhangyong Hu
AZAnnan Zhang
Annan Zhang
ZWZhiyong Wang
Zhiyong Wang
YLYang Li
Yang Li
By the controlling of variable, the influences on the film interface strength that filmline molding process had were investigated. The interfacial bonding strength under the circumstance where various of processing parameters (temperature, film thickness, injecting speed) were combined was measured through a normalized 90° peel test. And we used Superhigh magnification lens zoom 3D microscope to observe the Interface structure around the interface and the section of interface was observed too. To profoundly study the interfacial bonding strength mechanism, using the numerical simulation method, we analysed the temperature changes of the interface. And the crystallinities in different processing parameters combination situations were monitored by thermal characterization DSC. And then we calculated the crystallinities of the melt at the interface, drawing a conclusion about the relations between crystallinity and interface strength. The results show that the process conditions are favorable for improving the crystallinity of the interface and have obvious effects on the strength of the interface.

16 February 2026 in Chemistry
Verified
Journal Article
Open access
PDF file
LXLinxiao Xu
Linxiao Xu
YLYuquan Liu
Yuquan Liu
JLJiahong Li
Jiahong Li
HWHangyao Wu
Hangyao Wu
YWYuanqi Wang
Yuanqi Wang
Yang LiuYang Liu
Yang Liu
Use of the morphotropic phase boundary (MPB) is a promising approach to enhance the electrocaloric effect in ferroelectric polymers. This is usually achieved by a composition method, and polymer processing near the MPB to tune electrocaloric response has attracted little attention. Here, the relative stability between disordered 3/1-helix and ordered all-trans conformations is leveraged by uniaxial stretching to improve the electrocaloric effect in relaxor ferroelectric polymers under low electric fields. It is found that the stretching technique enables a considerably more enhanced electrocaloric response in polymer composition near the MPB at room temperature, compared with counterparts corresponding to the relaxor phase. The electrocaloric-induced temperature change is found to be 4.5 K under a low electric field of 50 MV m−1 in stretched relaxor ferroelectric polymers at room temperature, corresponding to a 60% enhancement over pristine counterparts. This result highlights the critical role of polymer processing in optimizing electrocaloric properties, especially near the MPB, and this can be extended to improve other functionalities, such as piezoelectric response, in relaxor ferroelectric polymers.

30 June 2026 in Science China Materials
Verified
Journal Article
Closed access
PDF file
YWYuanqi Wang
Yuanqi Wang
HWHangyao Wu
Hangyao Wu
LCLan Chen
Lan Chen
SLSinan Lin
Sinan Lin
CLChenyi Li
Chenyi Li
Yang LiuYang Liu
Yang Liu